DLEX3370W (ABWEECI) LG Dryer - Instructions

This was all pretty straightforward with the helpful video hosted on this site. The only issues I ran into was I had a seized screw that stripped and I had to drill it out and replace it. Also, I had to disassemble the front and rear a little bit further than what is shown in order to install the new roller axles. I was pleasantly surprised that I did not have to worry about the triangular retainers, because the replacement rollers/axles use an improved metal retaining pin. Overall, I'm very happy and the dryer is nearly silent now. It was a bit of a challenge but I took my time and gave myself breaks throughout the morning rather than banging my head against the wall.

Unscrew the screw, remove old part, place in new part, replace screw and you are done.

Simple replacement

An appliance repairman determined the problem which was that it needed new pulleys and thankfully PartSelect carried them. He installed them in an hour and my dryer runs fine now.

Removed cover replaced bulb

Viewed YouTube video form parts select to take dryer apart. Very easy to do if you just follow instructions in the video. Nothing too hard to do. Of note the 4 pack roller assembly is a whole unit, so you’ll have to replace the stem unit the old rollers use and not just replace the roller wheels like in the video. That is a different part number from LG. The front 2 are pretty straight forward to unbolt and replace. The back 2, especially one on the left is tighter clearance even with a wrench. If you’re able to pull whole dryer out and take back off, it’s an easier to get the one on the back left.
Also replaced belt just because i had it open, I replaced thermistor previously after getting a Te5 code about a year ago so that helped in taking it apart.
Would recommended doing it all since you’ll have it open.
Once replaced, everything ran again.

Removed the two screws holding the dryer door strike/locker assembly in place, removed the old and put the new in its place and replaced the screws.

Followed video provided on site

FIRST REMOVED THE LID ON TOP OF DRYER.THEN THE CONTROL PANEL AND THE STEAM TRAY. HAVE TO UNCLIP TWO HARNEST CONNECTORS. REMOVED THE FACE PLATE THAT HOLDS THE DRYER WALLS TOGETHER ALSO REMOVE TO SENSOR HARNESS CLIPS. .REMOVED THE BELT FROM MOTOR. TOOK DRUM OUT . UNCLIPPED MOTOR COLLAR SNAP CLIPS DISCONNECT THE MOTOR HARNESS. INSTALL NE MOTOR AND CONNECT HARNESS INSTALL CLIP . REINSTALL DRUM AND PUT BELT ON. CONNECT HANESSES AND INSTALL FACE PLATE. INSTALL CONTROL PANEL AND THE TOP LID.

I did as I was told (by my wife). Bought the machine from Home Depot - no side vent kit - had them complete the installation today when the kit came.

To install the repair part took about 5 minutes. It took a couple hours to take apart of put back together. Unfortunately the part I replaced was not the problem. I still have no heat. My own fault for not testing the parts before ordering. It seems there is no ignition of the gas for the hot air flow. I would be grateful for any suggestions. The video was FABULOUS...really step by step, screw by screw. Thanks for that. Barb Swenson

My cleaning lady brought her handy husband over Saturday to help me. The only tool we used was a Phillips-head screwdriver. I went online earlier in the week and found a good video put out by Repair Clinic and another one I found on You-tube on how to disassemble the dryer. After watching several times, I knew I could do it. We worked together, I cut my hand on the inside edge of the control panel, but, when I hit a snag, we watched that part of the video again and worked right through. Replaced the Thermistor, NTC first, not a problem. Then the Heater Assembly, not too difficult. I couldn't find where one of the remaining parts went, so, we reassembled the dryer and gave it a try. Worked like a charm. We did remove a lot of lint from inside the cabinet and around the felt liner on either end of the drum. It works like it did when it was brand new. Highly recommend to work with someone, so, you don't get frustrated. I am 65 years old and this was a no brainer for me, although I am somewhat mechanically inclined. Very empowering to accomplish this repair. Just follow the video.

I took the top off, I disattached the front and took the front top of dryer off, taking the front of dryer off, detached the belt and took the drum out, found the wheels took the plastic triangle off and took the wheels off and replaced wheels, then did everything in reverse and no more thumping. just remember to unplug unit before working on it. And also Part Select is a very good site and place to get parts, very fair priced and very professional.

I had ask how to get the top off., it was simple ,take 3 screws off the bottom angle bracket .and slide top back about 2" then lift.then remove the front panels. '

Removed the heating element, tested it, purchased a new element and installed.