RV1365ES LG Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- chet from WIMAUMA, FL
- Parts Used:
- 4581EL2002L
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Drum roller seized up
Handed the parts to my son-in-law he's very mechanically inclined had the job done in 20 minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harley from OKLAHOMA CITY, OK
- Parts Used:
- 6931EL3003D
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
when you push start button dryer does always start
order start button and was sent thermal, reordered and rep sent me a button that was not for my machine even though she had model no.,called third time and was told I had to order new control panel but they were not being manufactured any more.so it is not fixed
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Jenkintown, PA
- Parts Used:
- 6931EL3003D
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Added air diverter on exhaust hose and blew out heat limiter fuse.
Entered dryer from rear exhaust port. Removed 2 screws and 2 clip on wires. A little awkward of process but superior method over disassembly of drum and main parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dave from SAINT JOHN, IN
- Parts Used:
- AGM30045804
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
igniter would not light
Initially replaced igniter. Didn't think it was bad though. Read other suggestions on another website. None were the correct diagnosis for my situation. And when I figured it out they did not offer correct part. The dryer thermistor temp sensor (probe sensor) is what I replaced. Found it on Parts Select. I did replace other parts also. But that's the one that ultimately was the issue.
Was not hard at all if one is even a little handy.
Was not hard at all if one is even a little handy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Beverly from AMITYVILLE, NY
- Parts Used:
- 5231EL1001C
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dryer Filter had a whole in it.
Removed the old damaged filter and replaced it a new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kimberly from COMMERCE CITY, CO
- Parts Used:
- 5231EL1001C
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Lint filter cracked
Put the new lint filter in and it was completed
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patrina from Elberta, MI
- Parts Used:
- 5231EL1001C
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Filter edge cracked
Take old one out and slide new filter in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peggy from San Bernardino, CA
- Parts Used:
- 4581EL2002L, 4581EL2002L
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Dryer quit spinning
One of the roller assembly froze up & had a flat spot on it. There for causing the drum not to rotate. Pulled it out replaced the roller & up & running.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brent from HINCKLEY, UT
- Parts Used:
- AGM30045804
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
No heat
Pull off the top and front of the dryer and reached in and replaced the part it was easy. Had to clean all the dryer out real good with from the lint
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sal from MORENO VALLEY, CA
- Parts Used:
- AGM30045804
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Not heat
Followed the instruction on video.was great after three parts now is OK .we have heat.still cheaper than having it service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Mendham, NJ
- Parts Used:
- 6931EL3003D
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
Heater wouldn't get hot - suspected thermal fuse
Removed the top, the control panel and the door. The heater assembly came out thru the front, without having to remove the drum. Easy replacement
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kevin from MASHPEE, MA
- Parts Used:
- 4681EL1008A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set, Wrench (Adjustable)
I would turn on the dryer it would run for about 10-20 seconds and then shutoff, and could smell something burning
There’s all sorts of videos on it I watched. It was actually very simple
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bob from Holiday, FL
- Parts Used:
- AJQ75298102
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Thumping noise when on
watched the video on line then did the repair, very easy to replace
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- marty from NEOSHO, MO
- Parts Used:
- 6500EL3001A
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
HST code given by dryer
Called LG on the phone and they gave the button presses for diagnostics, which then gave the HST code, saying the Humidity sensor was bad.
The part was described as the Humidity sensor module. Actually it's just the wire leads for the sensor which must be electronic and only accessible by disassembling the dryer. There were descriptions about cleaning the wires, perhaps because some people use dryer sheets which cause a buildup on the wires and prevent them from doing their job. I use wool balls and have no buildup on my wires and replacing them did not fix the sensor, because the module accessible inside the dryer is not the moisture sensor, but only the wire leads.
The part was described as the Humidity sensor module. Actually it's just the wire leads for the sensor which must be electronic and only accessible by disassembling the dryer. There were descriptions about cleaning the wires, perhaps because some people use dryer sheets which cause a buildup on the wires and prevent them from doing their job. I use wool balls and have no buildup on my wires and replacing them did not fix the sensor, because the module accessible inside the dryer is not the moisture sensor, but only the wire leads.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gabriella from Lexington, VA
- Parts Used:
- 5231EL1001C
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dryer lint filter lining was falling apart and lint was not being filtered
Ordered a new Dryer Lint Filter Assembly that fit my LG electric dryer.
Was this instruction helpful to you?
Thank you for voting!