KEYS850LQ1 KitchenAid Dryer - Instructions

Numbet one - unplugged the dryer. Then disassembled dryer (front panel, loosened vent from top panel and removed drum). Removed motor after carefully documenting wires and their corresponding numbers, along with pictures. Read directions several times to assure we understood process. Followed instructions for replacing connectors. Used pliers and screwdriver to install motor clips. This took numerous, patient attempts. We also had to partially remove the vent in order to reinstall the motor. Then replaced drum, front cover, reattached vent to top cover. Reattached outside vent hose. Plugged dryer in and tested it. Motor replacement worked fine and fixed the problem (squealing).

Unplugged washer,removed the two screws by the lint trap,moved the top foward lifted the top (it'shinged in the back )the switch is right inside the door top right hand corner removed the two screws that hold the switch in place used a flatblade screwdriver to seperate the connections pulled off the old installed the new switch put every thing back together worked as though it wes never broken

I looked at the parts breakdown to see how it cam apart.

I tore the dryer down,
1. removed the door
2. openned the top
3. removed front panel
4. removed fron bulkhead
5. removed belt and drum
6. removed back cover
7. removed the ductwork
8. removed the fan (this is the hardest part, it is very tight on the motor with left hand threads, there are flats on the (inside of the dryer)fan where the motor shaft goes into the fan for a wrench and you can put a socket on the front pulley on the motor. I ended up just knocking the center out of the fan and replacing it.
9. removed the motor and cleaned the entire unit
10. reinstalled everything in reverse order. Note:I went ahead and replaced the idler pulley and the rear wheels that support the drum, and put a new belt in (just about
everything that could fail) I spent about $200 to keep a $1200 dryer in service at least another 7 years.

Unplug dryer, remove two screws in lint screen door, using a pry bar or stiff putty knife, gently pry up on both front corners to release the clips holding the top down. Use a 5/16" nut driveer two remove the two screws inside at the top of the front of the dryer, remove the two wires on the door switch. Open door enough to get your hand in to support the drum, now lean the front out at the top and let the drum rest. Grasping the front at the top on both sides gently lift up to release the clips securing the bottom front. Release the door springs,open door and replace the hinges. Reverse to reassemble.

Solution: electric motor replacement as the integral centrifugal switch lever (plastic cam) wears over time causing the start windings' switch poor contact. Took it all apart, (back panel, front and top) including lifting the drum out to completely expose the motor. Needed to wrench the plastic fan from the inside motor shaft. Tricky part was swapping the original pulley (6 rib belt, still good) for the one supplied for 4 rib belts. I needed to file another flat onto the other side of both motor shafts (old and new) to break them free, using a vice to secure the pulleys. The dryer works perfectly! It's a great dryer that can be repaired by a determined novice. The enclosed instructions were helpful, although if followed about cutting the original motor shaft to obtain its pulley might require drilling the shaft from the pulley = nonsense. Thanks again Parts Select.

Followed the PartSelect instruction video.
Basically opened the dryer.
Took the drum out.
Took the broken motor out.
cleanned the dryer since I had everything opened.
Replaced motor, pulley, old belt.
My 20 years old dryer is running like brand new.

I needed to remove the front lower cover, very easy as it is held on with clips only so I used a flat head screw driver to pop it off. I had to remove the lint filter and then there are two screws attaching the top cover of the dryer to the internal lint filter tray. The top of the dryer can then be opened front to back I again used the flat head screw driver to pop the top open as it has two clips at the front corners. It helps to have someone to hold it open or a rod of some type to keep it open. You can now lay the belt on the top of the drum and work it down the back side by pulling forward on the drum itself to seperate the drum from the seal that presses aginst the back side of the drum. I then went from the lower front to retrieve the belt now draped over the drum and pinched the belt to pass it through the tensioner and over the drive pulley. looking at it from the front the belt will come down the right side of the drum under the tensioner pulley around the drive pulley across the bottom of the drum and up the left side. The belt sits almost in the middle of the drum not against the back lip where there is a groove that might be confused as a place for the belt to ride that is where the seal sits then reverse the process to reattach the top to lint tunnel and reattach front cover and you are good to go . i would suggest vaccuming any old dust/ lint whlie everything is open as this reduces the chance for catching on fire I was supprised as to how much lint was loose inside the dryer cavity itself and our dryer is gas and the flame is an open flame.

We took the screws off of the back, took out the thermal fuse and replaced it with the new one.
We watched a video of how to do it which made it so easy.
Works great!

The most difficult part of this repair was making sure I purchased the right part !!! Part Select.com has a great website with pictures of almost every part you could ever need. I was able to select the right part and from there the repair was easy.

Troubleshhot problem, used multimeter to verify current to motor. Once that i was sure motor was getting proper voltage, I used a meg-ohm meter on A/C motor windings and physically tried to turn motor and found that it was siezed. I then cleaned inside of unit inspected belt and drum rollors. Due to the cost of the items, I decided If I was going to replace the motor I should replace all moving parts, and install new belt. Everything went easy. WHAT WAS MOST IMPRESSIVE! was that the Parts people sent the correct parts on time the first time, with no hiddin charges. There web site should accurate diagrams of parts and internals of machine. I was really pleased and will use this service again. Thank you

I identified the correct catch of the three that were included in the package by matching its number to that on the old catch that I had pried out of the door using a flat screwdriver. I centered the new catch over the square hole in the door and pressed it into place. Then I used some needle-nose pliers to twist and remove the metal pin that fits into the catch from the main dryer housing. I replaced that with the new piece included in the kit, gently tapping it into place with a hammer. The repair complete, the door worked perfectly. Thanks for your help and for the speedy delivery of the kit.

I watched all the videos with Steve. He was very helpful in his presentation of the repairs. Due to the age of the dryer every thing was replaced and was very easy to do. Thank you Steve and PartSelect for making these repairs possible and easy

Replacing the part was easy: unscrew the old one from the front of the dryer after opening door, disconnect and replace with new one. Getting to it was a bit more difficult: Remove 6 screws from the back, 4 that hold the back of the top down and 2 that hold the control panel in place. You had to remove the control panel to free up the wiring bundle (held in place by a tie wrap inside the control panel housing) so you could move the top forwards enough. Then remove the top of the dryer by lifting the back up slightly and moving it forward to disconnect from attachments in the front and move aside to gain access to the switch.

Took a bit to first figure out how to get the front of the dryer off in order to access the motor, wheels, and belt, but found a "how-to" online. Once I had that, the rest was easy.

Lubricated motor and guide wheels but squealing still there. Then noticed the "idler pulley assembly" (the part that keeps the belt tight against the drum) looked a bit old and worn. Ordered a replacement part on this site because it was much much cheaper than a service call, installed it.... and NO SQUEAL!!!

Removed 2 screws in the lint filter and popped off the top. Removed the 2 screws holding the front panel on. Slid the drum off and set aside. Replaced support rollers. Placed the belt over the drum and placed the drum back in the dryer. Wound the belt over the tensioner and motor pulley. Turned the drum to keep seal from folding up. Replaced front and top.

Tip: Use bungee cord or rope to hold top up and out of the way while doing this job.