79681472210 Kenmore Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Sal from MORENO VALLEY, CA
- Parts Used:
- 6323EL2001B
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Not heat
Followed the instruction on video.was great after three parts now is OK .we have heat.still cheaper than having it service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- joaquin from MIAMI BEACH, FL
- Parts Used:
- EBF61496102
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dryer work but wouldn’t shut off when finished cycle, had to shutoff from breaker
With a thin flat screwdriver I was able to pry out the old door switch, I replaced it with the new door switch, pushed back in dryer and so far is working since I installed a month ago.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- marty from NEOSHO, MO
- Parts Used:
- 6500EL3001A
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
HST code given by dryer
Called LG on the phone and they gave the button presses for diagnostics, which then gave the HST code, saying the Humidity sensor was bad.
The part was described as the Humidity sensor module. Actually it's just the wire leads for the sensor which must be electronic and only accessible by disassembling the dryer. There were descriptions about cleaning the wires, perhaps because some people use dryer sheets which cause a buildup on the wires and prevent them from doing their job. I use wool balls and have no buildup on my wires and replacing them did not fix the sensor, because the module accessible inside the dryer is not the moisture sensor, but only the wire leads.
The part was described as the Humidity sensor module. Actually it's just the wire leads for the sensor which must be electronic and only accessible by disassembling the dryer. There were descriptions about cleaning the wires, perhaps because some people use dryer sheets which cause a buildup on the wires and prevent them from doing their job. I use wool balls and have no buildup on my wires and replacing them did not fix the sensor, because the module accessible inside the dryer is not the moisture sensor, but only the wire leads.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lorraine from SEQUIM, WA
- Parts Used:
- 3550EL2001A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Lamp cover broke
Unscrew the screw, remove old part, place in new part, replace screw and you are done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kevin from MASHPEE, MA
- Parts Used:
- 4681EL1008A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set, Wrench (Adjustable)
I would turn on the dryer it would run for about 10-20 seconds and then shutoff, and could smell something burning
There’s all sorts of videos on it I watched. It was actually very simple
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bob from Holiday, FL
- Parts Used:
- AJQ75298102
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Thumping noise when on
watched the video on line then did the repair, very easy to replace
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Duane from TROY, TX
- Parts Used:
- 6913EL3001E
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Light bulb in dryer burndt
Removed cover replaced bulb
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- NANCY from ATASCADERO, CA
- Parts Used:
- 4581EL2002L
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Dryer was making a terrible sound.
An appliance repairman determined the problem which was that it needed new pulleys and thankfully PartSelect carried them. He installed them in an hour and my dryer runs fine now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from RIVERSIDE, CA
- Parts Used:
- 4581EL2002L
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set, Wrench (Adjustable)
Loud rumbling noise
Followed video provided on site
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from Michigamme, MI
- Parts Used:
- 6931EL3003D
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
thermal fuse went out
Watched a repair video. Very easy to replace, about an hour to repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tim from Tavares, FL
- Parts Used:
- 6500EL3001A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Had an issue with the dryer not drying the clothes in the allotted time and turning the dryer off. I knew it was still getting heat so I googled the issue with suggestions.
I watched a YouTube video with how to take the dryer apart and remove the sensors. I followed the what the instructions were removing the top of the dryer and then the front panel. Once that was removed it was a matter of removing 7 more screws and the lint collector piece came off. Popped the sensor pieces out. Cleaned the inside of the dryer and reinstalled a total of 5 parts and dryer is working fine and the clothes are drying in the allotted time it use to take.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Omar from SILVER CITY, NM
- Parts Used:
- 4681EL1008A
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
CHANGED OUT MOTOR
FIRST REMOVED THE LID ON TOP OF DRYER.THEN THE CONTROL PANEL AND THE STEAM TRAY. HAVE TO UNCLIP TWO HARNEST CONNECTORS. REMOVED THE FACE PLATE THAT HOLDS THE DRYER WALLS TOGETHER ALSO REMOVE TO SENSOR HARNESS CLIPS. .REMOVED THE BELT FROM MOTOR. TOOK DRUM OUT . UNCLIPPED MOTOR COLLAR SNAP CLIPS DISCONNECT THE MOTOR HARNESS. INSTALL NE MOTOR AND CONNECT HARNESS INSTALL CLIP . REINSTALL DRUM AND PUT BELT ON. CONNECT HANESSES AND INSTALL FACE PLATE. INSTALL CONTROL PANEL AND THE TOP LID.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from CUDAHY, WI
- Parts Used:
- 6323EL2001B
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
no heat
To install the repair part took about 5 minutes. It took a couple hours to take apart of put back together. Unfortunately the part I replaced was not the problem. I still have no heat. My own fault for not testing the parts before ordering. It seems there is no ignition of the gas for the hot air flow. I would be grateful for any suggestions. The video was FABULOUS...really step by step, screw by screw. Thanks for that. Barb Swenson
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ROBERT from DAWSONVILLE, GA
- Parts Used:
- 3911EZ9131X
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Install aftermarket side vent kit
I did as I was told (by my wife). Bought the machine from Home Depot - no side vent kit - had them complete the installation today when the kit came.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from Whittier, CA
- Parts Used:
- 4581EL2002L
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers
Thumping sound when dryer is on.
I took the top off, I disattached the front and took the front top of dryer off, taking the front of dryer off, detached the belt and took the drum out, found the wheels took the plastic triangle off and took the wheels off and replaced wheels, then did everything in reverse and no more thumping. just remember to unplug unit before working on it. And also Part Select is a very good site and place to get parts, very fair priced and very professional.
Was this instruction helpful to you?
Thank you for voting!