99937CE Kenmore Dryer - Instructions

I thought it had to be the igniter so I replaced that part. The dryer still did not start. I replaced the high limit and hoorah dryer works. Two weeks go by, the dryer is drying the clothes but my wife smells gas in the laundry room. I replaced the coil pak on the gas valve. My wife says she still smells gas. I replaced the radiant flame sensor and no gas smell for 2 weeks now.

After the Radiant Flame Sensor was installed, the problem remained. An appliance repair person then replaced both coils, and that fixed the problem.

Replaced the flame sensor since it was believed to be the problem contributing to the lack of flame in this gas dryer. However, this part did not correct the problem.

I just knew it had to be the heat sensor unable to activate the actual ignition. I following the directions and video for the installation of the heat sensor #PS344761. It went very smoothly. Upon completion of the installation, the click, then the flame roared to life and I felt like a real do-it-selfer!! This was short lived. The wetness of the clothes had no effect. Something I did not do and I certainly know better was to check and see what was taking place before I replaced the "damaged" sensor. No, I was just so sure there was no need of that. You say, put the old back in and watch what happens....I recycled the old one immediately. Sigh! We have had two weeks of rain and I'm really tired of damp clothes everywhere. I will read other alternatives and report back. DClark, TX

The part came in very quickly. If you know how to remove the front panel, it is very easy to repair. The hard part is to diagnose the problem. The first thing to check is the igniter. If it comes on then you look for faulty limit switches. If you have lots of training in electronics and appliance repair this is very easy, if you do not I would not try this. I have 40 years in the repair business, It still took me 1hr. to find the problem. the switch was intermitted, one time the dryer would work the next time it would not. Good luck and happy repairs.

I feel like I have a new dryer now. I replace 3 of the 4 main components using parts select. Not only did they ship next day, but the tutorial videos with Steven were right on the money and self explanative.

Since there were no troubleshooting steps, I had to start replacing the items according to the list that showed the parts that have fixed the problem for others. I ordered one at a time until I got the part that fixed the problem. I went through 4 parts before I replaced the gas solenoids which is what fixed the problem. By the time I was done, I could disassemble that dry in about 5 minutes or less.

Unplugged electrical cord to dryer. removed the front cover 2 screws on the bottom. Lifted front cover off. Unplugged the 2 wires going to the old flame sensor. Used nut driver to remove 1 screw holding the flame sensor in. Removed old sensor replaced with new one. Reattached the 2 wires back on to the new flame sensor. Tested. Flame stayed on longer! Dryer works great dryer is 20 years old and still running like new now. Part was the exact match I needed.

unplugged dryer and removed front panel. removed the screw that holds flame sensor and unplugged electrical wires. then replaced with new. Did not solve problem so I ordered the replacement coil kit and installed them using phillips screw driver and this solved problem. Dryer is working fine now. I found this site very helpful and would recommend it to a friend.

Opened the bottom panel w/ 1/4 nut driver to access the flame sensor and easy fix.

Followed the easy to understand how to video. The drier was up and heating again in less then 30 minutes.

First I replace the Radiant Flame Sensor, but the problem remain. Then replace the two coils and the igniter. Dryer works like it should. If I were to do it over, I would have replaced all 4 components to start with. Thanks for good advice and great service.

Unplugged dryer from power source, used putty knife to release latches that hold top on, tilted the top out of the way, unplugged door lite, located the radiant switch, removed 1 screw,then undid 2 wires & lifted out switch. Reversed procedure plugged in dryer....wa la had dried a large load of clothes, took 1/3 the time to dry clothes at last. Thanks "PartSelect"

After getting on-line to your site we looked up what the problem could be after receiving the dryer from a friend to transfer from electric to gas to save money. First we thought it to be the ignitor and after receiving it so quickly it still didn't work so went to your site again and found the Flame sensor. They were both defective and now it works wonderful!!! Your site also explains what and how to repair the appliance, which my husband appreciated! We are glad you contacted us because your site did not show that we could send you and e-mail Thanking your company for the excellant service we received. Your prices can't compare to other companies either, we were amazed on the differences. When you say the next day delivery, you mean the next day!!! Thankyou and you are now in my Favorites if ever needing parts for other appliances we own.

Ordered thermal fuse and cycling thermostat