11064086202 Kenmore Dryer - Instructions

Received in two days, open box, installed part. Pretty easy, fast service. I'm a repeat customer and will use these guys in the future.

Inside the dryer tub, remove the filter housing by removing two phillips head screws. Unplug the sensor wires, note when replacing wires, black wire goes on upper sensor.
Separate filter grill from housing. Using the pliers, compress the tabs on the sensor plugs and push it thru the grill. The small blade screwdriver may come in handy here to pry up on sensor to assist in pulling the plug end through the grill. Replace the sensors by hooking short end into grill and pushing the long end through the grill. When replacing the housing to the dryer, the most difficult thing is getting the screwdriver onto the recessed screws. Be sure to put the tab on top of the housing under the dryer frame when rotating the assembly into place.

I just followed the videos I received with the order and everything went really well. This dryer was a little different than the video, but the process was the same. The HE3 does require 4 drum rollers and I had only ordered 2. However, there was only one bad roller, so I installed both on the back of the drum. The two front rollers are pretty easy to get to if they go bad. The idler pulley was completely worn out with an 1/8 inch groove worn off to one side. PartSelect made this an easy project!

Popped the lower cover off the dryer, found the thermal fuse and thermostat mounted on the heating tube. Removed the screws with a nutdriver, swapped wires to the new parts, and reinstalled. Then I spent 30 minutes vacuuming 13 years worth of lint and crud out of the machine - it was pretty gummed up in spots, which is probably the cause of the failure.
I have a 25 foot run of hose from the dryer outside, so I replaced that with 4" metal ducting. Clothes dry much faster now!!! Maybe my electric bill will go down (fat chance :) )

Opened the lid and removed screws hollding switch to cabinet. Had to use magnifying glass to find locking mechanism on the electrical harness. Used small bladed screwdiver from my computer maintenaqnce kit to disengae lock. Hooked up harness. Replaced screws and shut lid. Main difficulty is my near vision. Requires use of a magnifier I am 80 years old). Your video is great. Gives step by step instructions.

I used a screwdriver to remove the old part and pushed the new part in with my fingers, it was very easy. If I could do it, anyone can. I was a lot cheaper then having a repair man come to house. I am very glad I found your site online, I will definitely be using your company again.

My dad was ready to spend $2000 on a new washer/dryer (he has to have a matching set!). Anyway, his dryer would not generate heat. A google search turned up partselect.com, which walked me through the procedure to see what we needed.

It turned out to be a simple to replace $25.00 part! The dryer is drying as if it was brand new. Saved $1,975. Hehe.

Thanks, partselect!

Used my Whirlpool Dryer User Instructions Manual and followed instructions and used the Cabinet Parts page to see the diagrams.

Partselect order confirmation email included video instructions of how to change the door switch on my model dryer. Like others I had a pause with the switch connector. I viewed the video again and the instrucions showed to use the putty knife tip to push down on the connector tabs and it came right off. Replacing the switch was easy as the video instructions. Fast shipping of the right part at a good price. The video was pricless. Thank you partselect.

it took loess than 10 minutes to change the door switch after watching the repair video

Found a U tube video to be useful. Remover 2 screws under the filter lid. Used a putty knife blabe wrapped in masking tape to unclip the lid. 2 screws to remove the switch. Biggest difficulty is seperating the electric connector. installed replacement switch and closed lid.....reality is this is a 15 minute repair. The extra time was to take the time to remove dust and lint from behind the dryer. Easy repair.

I typed in on my brouser Repair Kitchen Aid Dryer door switch.
And on You Tube up came several videos showing me how to ewmove the switch and install the new one.

The hardest part of the job was not instaling the switch but the dryer Vent hose from the back of the dryer after I puled it away from the wall, it disconnected and the I had to Pull the Washer out which was right next to it so I could put the vent hose back to the dyer. I has to disconnect the Hot/cold water line pull the washer out connect the dyer hose reconnect the cold /hot water lines and yada yada yada

Unscrewed the bottom panelof the dryer and located the thermistor through the schematic for my machine. Removed the old one and put the new one in the same way. No more E1 problems and all cycles now complete themselves.

I had already taken the coil out of the heating housing to check for a break in the heating element. I took this time to vacuum out all the lint inside the cabinet. I slid the new coil into the housing and reattached the wires. Plugged the dryer back in and turned it on to make sure the coil heated up. It worked so I put all the screws back in and fastend the front back on and were in bussiness!

unplugged from elect power.took off front lower panel.removed heater heat shield w/1/4 in nut driver,could see heat element. it looks like at thin metal twisted phone cord. i used a continuity tester to establish if there was a break in it. there was. i removed 2 1/4in screws on the right side of the element,marked wire placement slid out old element & slid in new one put screws back in connected wires,put heat shield back on . tested dryer ,ok good to go put on front cover.!!!!! PS sears parts wanted 15$ more