11076995800 Kenmore Dryer - Instructions

I unplugged the dryer from the electrical outlet, removed the back of the unit and checked the heating element for continuity. There was no reading. I then removed the housing and heating element and visually inspected it. The coiled wire was broken in two places.
I then did a Google search with the model number and found Parts Select. I placed my order Sunday afternoon and the part arrived the following Wednesday. That evening it took about 20 minutes to install the new element,put the back on the dryer and re-attach the exhaust tube.
The old dryer is as good as new again.
TJ in Boise

IT WAS EASY, TOOK OUT THE OLD ONE AND PUT IN THE NEW ONE!! ANY ONE COULD DO IT.

Timer knob.....took new knob out of protective shipping bag and installed it on the existing timer stem. It took less than one minute.

Door catch kit......removed original female latch part from dryer door and installed new one by pushing it in the hole left by the original part.

Went on-line Chat and described my problem to a very professional and patient representative who requested the necessary information needed to replace my filter. Note: Due to the age of the my dryer, Sears no longer had a replacement. I'm thankful that this site was able to accomodate my need.
The repair, or should I say replacement, was as simple as pulling out the old filter and replacing it with new. Only tools, my two hands.

i took the face off dryer and removed the belt and drum then removed the lint trap from back to clean and have access fan then removed the retaing clips holding the motor then with two adjustable wenches unscewed the motor from fan took out motor and replaced in reverse order all you needed was some common sence to do this i though it was easy to do greats parts fit perfect thanks tommy

I followed the video. So easy..

The first step was to check the electrical supply to make sure I had power 120 volt. I unplugged the dryer and turned off the gas supply and turned the dryer around so I could have access to the back panel removed panel to access the wiring harness and safety thermostats. All switches and wire checked good with my ohmmeter .I pulled off the front kick panel and checked the electrical schematic and found the door switch was in the circuit to check it I had to lift up the top and pop out the front to access the door switch checked switch and found it defective. Replaced switch vacuumed out dryer and vent reassembled dryer and all worked good.

I am a teacher and teaching is my game. I have always, with my four children, taught them to do mechanical work themselves. I and most of my children have a PhD, but in having said that, I confess, we come from a very mechanically talented family. It shows and proves to be of great benefit.
OK, so much for the intro.

I gave my daughter the tools and said, "What do you think is wrong with the dryer and where would you start?" She tested it and said, "The motor is running, but the tub is not turning thus I conclude it is the belt because I can hear the motor running eliminating that as a cause.

She then opened the top, looked around and removed two screws from the lint catcher. She looked it over, looked a me, I shrugged my shoulders and she then took a rubber hammer and popped the top off. Don't ask me how she knew that, but I think she saw the rubber pins through the crack between the case and top. She raised the top after removing two screws in back to relieve the simple hinge and also disconnected the wiring clip and sure enough, the broken belt was inside the cabinet. We called you, the best, fastest and most accurate service on the Internet and ordered a replacement. I would like to add, the price is always more than fair and delivery very prompt.

When the part came, my daughter took it up to our laundry room and within twenty minutes, she tested it and everything was fine. She did smell a little burning smell which might be attributed to a new belt or the fact that there was no clothing in the dryer.
Thank you so very much.
Dr Robert E McGinnis

I followed the instructions on the video and it was simple. The hardest part was vacuuming out 32 years of lint from around the motor and igniter. I was lucky there was never a fire in the dryer.

I disconnected the dryer from the electric. I removed the lid to the dryer by first removing the lint door screws and prying the lid off properly. Disconnected the wires to the door switch. Removed the screws from inside the door and carefully removed teh actuator. Seperated the actuator from the switch and replaced the broken actuator. Reinstalled the actuator and switch and screwed the assembly back in place. Reconnected the wires, lowered the dryer lid and screwed the lint door screws back in place. It Worked perfectly.

You can buy the switch AND lever/latch, but partselect had lever by itself which is all I needed. Pay attention to orienation of lever around switch when you take old latch off and attach new. Also, be careful to not drop new lever behind/beneath clothes dryer drum. Took my wife and I a while to fish it out. I have replaced heating element, and other parts. At some point it will be time for a new dryer...

The original part is no longer manufactured. However, PartSelect provided a cross reference from the original part number to an acceptable replacement. The new part simply had to be lined up and pushed on to the shaft. The time required to install the replacement was approximately one minute.

all that was required was to push the catch into the slot notools needed.

Did not hear the "clicking noise of the door switch when the dryer door was shut. First I unplugged the dryer from the socket. Next I removed the two screws that hold the lint filter receptacle. Next I pried the top of the dryer open with a screwdriver. Next I removed the two screws that held the switch actuator spring in place located just inside the top of the door. Then I removed the old spring from the door switch and replaced with the new. Not too difficult once the problem was diagnosed.

I realized from this issue years ago that it was porbably the heating element. I took the dryer to the garage and remove the back and figured out how to get the heating element out. Once I had it out it had a break in the coil so I knew I needed that part. I hit parts select on line and ordered the part. I left everything in the garage and waited for the part. In a couple of days it came and I put it in and took the dryer back to the laundy knook, gave it a test run and Its all good!