11076901690 Kenmore Dryer - Instructions

Take pictures along the way.
1. Remove lower front panel using screwdriver to lift up on tabs on top of panel.
2. remove door
3. unplug moisture sensor plugs
4. remove lint trap
5. on back of dryer, remove screws holding upper lid
6. slid up lid forward just a small amount, its hooked in towards the front of the upper lid. you will need to do this so you can can remove two screws under the lid holding the front panel of the dryer on
7. remove the front panel screws mentioned in step 6.
8. Remove lower front panel screws
9. remove front panel
10. reach into dryer at the bottom and release tension from belt pulley, sliding the belt off. (make a note of how the belt is routed around the drive and idler pulleys)
11. slide out tumbling drum
12. with drum removed, use socket wrench and socket to remove old idler pulley.
13. install new idler pulley
14. reinstall tumbling drum
15. slide belt back around tumbling drum, looping belt around drive pulley and around idler pulley.
16. When belt is installed, rotate drum a few revolutions to ensure belt rides correctly.
17. Reinstall front panel
18 slide top panel back into place and secure with screws from back
19. reinstall door
20. reattach moisture sensor plugs
21. reinstall lower panel

You tube and supplied video directions for the make and model. Follow step by step and the repair went easy. Worried when removing the dryer drum but it went smooth.

YOU NEVER SENT ME THE PARTS!!!
I had to drive to a parts store to find them. On January 17, 2024, I tried to call you when the parts did not arrive and your recording said there were no reps available and you hung up. WE CANNOT GET HELP TO CANCEL THIS ORDER. We have been going in circles with PartSelect and shipping. SO, how do I get my refund of the $107.26 for the parts that I never received!!

remove top, front, drum, fan fan housing, replace motor

There are two screws that hold the switch in place. And two wires connected to the switch. The most difficult part of replacement is to place the new switch and hold it in place to reinstall the mounting screws. The space to work in is limited unless you remove the front panel from the dryer, which I opted not to do.

Unplug dryer from 220VAC outlet

Remove bottom cover panel, slip a flat blade screwdriver into each clamp, and bottom piece becomes removable. Pull forward and lift bottom cover piece.

Pull up top section from dryer frame. Disconnect dryer door off/on contact three wire switch by pressing plastic connector together. You may need a small flat blade screwdriver to seperate connector.

Remove two Torx (T15 head) screws in the far left and right corners of the front door panel.

Remove two screws underneath dryer lint screen, be careful to not let front door and front cover fall forward. The rotating dryer drum will now be loose.

Underneath drum, there is a cover panel over the dryer motor. Likely you will find a bunch of lint all about. This dryer had likely not been cleaned in many years.

Remove screws on dryer motor cover.
Remove panel. Likely, you’ll more lint about.
After vacuuming, use a flashlight and hand mirror to locate belt tensioner, back side of motor. If your belt is not broken, press down on the tensioner spring and remove belt from tensioner and motor. Inspect belt, replace if worn. In this instance the belt was well worn.

Slowly pull dryer drum forward, walking belt along as you bring drum forward out of the dryer casing.

At this point you have plenty of room to access the one bolt holding the tensioner, in this instance it was a 13mm socket. Be careful to remove the tensioner springs before removing the bracket. Your PartsSelect is an identical match to the original one.

Install new tensioner, tighten slightly, then put springs back on.

Reverse this entire process to get your dryer back together and back running smooth and quiet as it was when new.

This dryer was quieter than its owners remembered it being back when new 15 years ago.

Well worth saving the $ doing your own work.

Good luck on your repair endeavor!

Followed standard instructions regarding removal of top first & then the front panels. Realized after following this process that I did not have to remove top, but only one of front panels to obtain access to moisture sensor. If I have to do this again, the replacement of sensor will be much easier.

Unpluged dryer power cord.
Removed lower front panel (two snap clips at top of panel)(Rear panel cannot be removed from this dryer). Removed blower/filter housing (held by two screws). Found blown fuse by using an ohm meter across the fuse terminals with one wire removed - no continuity. When new parts arrived, I removed two wires from fuse and four wires from thermostat. Removed two screws holding fuse and two screws holding thermostat, and removed both parts.
I then reversed the above procedures.
Dryer works great!
Total cost, including shipping, was $47.76

Ezee pezee lemon squeezee.

Took the back and top off of my front loader. I had checked on you tube for the problem and how to fix it and ordered the part. Just followed the directions on how to remove the old idle pulley and installing the new one. Dryer runs like new!

Not a handyman but this was an easy and cheap fix. Now the automatic settings are working and drying much faster. Unplug machine, front panel has 2 spring clips toward the edges that you stick a flat tool into and pull on the panel to open. Pull off the electrical connections from the old sensors by the right side of the lint screen. Needlenose pliers help with the one farther up there. Then just pull the old ones sensors out, stick the new ones in, reconnect the electrical and get ready to live the good life with dry clothes that don't smell musty.

Simply followed the video that accompanied the part confirmation. Removed the top and front of the dryer. Removed the drum and belt. Unbolted (1 bolt) the Idler pulley and bracket and bolted on the new one. Reversed the sequence of disassembly and tried it out. The only minor difficulty was slipping the belt over the idler pulley after the drum was in place. This is where a second set of hands might be helpful to hold up the drum, while the other person puts the belt in place. Other than that, this was a simple repair and probably saved a couple hundred dollars for about 1.5 hours of my time. Thanks for the video...it was right on point, and made the job much easier.

Removed the screws replaced the belt and lubricated the wheels and that fixed my Knocking and it runs like when I first got it

Very easy do it yourself repair, and saved at least $300.00. I watched a video and it took me less than 20 minutes to complete repair. Part fit perfect and I have already ordered another to keep as a spare.

I am a 75 yr old woman. I cannot afford to have a service call plus parts. So I ordered the part from this company and used the video instructions to install. Now this should have been a 15 minute process but I was being careful.. I installed and pushed start and Hooray I did it