1106117240 Kenmore Dryer - Instructions

I removed the old door catch by using a screwdriver to pry it out, then I popped the new door catch in its place and it snapped right in. It took less than 5 minutes to do the whole job.

take the old latch out and pop the new one in. Your repair kit worked perfect.

This was a classic easy repair and I am sure saved us bundles on a service call.

Reviewed the video showing how to remove the bad-order part and install the new part. No problem. Installing the new part was exactly what was shown in the video on the web page.

I used you-tube to troubleshoot and repair. Your part store was excellent to deal with. Delivery was prompt and cost was very reasonable. Thanks!

>removed 2 screws connecting the vent filter to the top lid of the unit (just in front of removable filter).
>Losing two screws at the back of the machine, just below control panel to allow free movement of the top lid on its hinges.
>Raise top lid & supported open.
>Now have free access to door switch (inside , front right fastened to front panel)
>removed the old switch
>fasten new switch (required new wire connector which was supplied with package) to existing wiring and replaced.
>Works perfectly!

Googled dryer won't start! From information on the Parts Select website, I determined it was possibly the dryer door switch. Checked the dryer to confirm status of door switch and found it broken! Ordered part and received it within 2 days (actually ordered on a Sunday and it shipped on Monday with receipt on Wednesday. Unpluged the dryer. Used information from Parts select website to remove two screws from vent filter, used screwdriver to pop the top of dryer at each front corner, removed two long screws from the old switch and replaced the broken actuator on the switch with the new actuator received from Parts Select. Note: It was easier to remove old switch with the wires removed from terminals (just pull off), replacing the wires after securing the switch and actuator back in place. Piece of cake, wife happy, received her king of the roost reward :>)) This is also a good time to clean the lint filter area and the hoses to prevent one of those 16,000 annual dryer fires!!!

drilled a 7/16 diameter hole directly in the center of the two mounting holes filed it square big enough so as the spring tip fits thru now the door closes on the spring which actuates the switch looks and works perfect.

Fantastic site and service !!! Using your site, I i'd my needed part in about 10 minutes. I received my Whirlpool dryer door latch part from you in less than 12 hours. Per your internet site instructions, I replaced the part in a few seconds (just popped it into the slot) and my wife had a working dryer for her Sunday wash. I would have been out $55 and 4 to 7 days waiting for a service call if I had used my home warranty service contractor. Using your service, the part(s) and shipping were just over $12.

Took 5 seconds, just snapped in the slot, didn't need any tools.

Took top of d then dryer loose then replaced switch actuator put dryer top back in place. Not that hard.

I first noticed that the tab of the door switch snapped off so the safety on/off switch did not work when the door was closed. I temporarily taped the switch closed so I could use the dryer. I found the model number from the unit and easily found the schematic and part description from the website. I placed the order and had the part in a few days. Problem solved. Thank you

ordered new latch kit and repaired, very easy thank you

Snapped latch into existing hole in 2 seconds. The pin that goes into latch was still intact. That's it ,real simple. The only problem I will hopefully not have in the future is the the mico-switch which is just hanging in there, the switch works but the lever that extends out from the face, that works with the door is partially broken off and the switch is no longer available on your parts list. The appliance is twenty-one years old. I am very happy with your service and I received the parts the next day, after I ordered them and I will be buying more parts in the months to come. This time it will be for my Kenmore gas stove and then a Kenmore refrigerator door hinge.

For 2 years, I propped a broom stick against my dryer door to keep it shut while it was running. Last Sunday night, I decided that it was about time to fix it. I found the PartSelect site, which was extremely easy to navigate, and ordered a replacement kit. It arrived in 2 days via Fed Ex and actually contained extras of each of the 2 components, in slightly different sizes. It took me about 10 minutes of eyeballing the parts to figure out how to place them and about 30 seconds to install the new latch parts. They fit perfectly. Great site, great service, I would highly recommend this site.