11069132413 Kenmore Dryer - Instructions

I watched the video on the websit and it told me and showed me just what to do. Exccelent video, Ordered the repair kit, got it in two days. Job took me about 10 min.

Removed back panel to get to inside. Removed drum etc to replace drum rollers (ordered repair kit also), replaced the idler pulley etc, now like new. Repair successful!!!! Thank you!

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

Removed the lower front cover of the dryer. Removed the lint filter and removed the cover from the air duct by removing two 1/4" bolts. Removed the two 1/4" bolts retaining the thermistor. Installed the new thermistor and covers.

Installed new belt and cleaned dust and wiped out inside of drum with Fantastic and clean sponge.

Took off the front of & lifted the top up. Pulled the drum out & replaced the two wheels that turn the drum, replaced the belt & replaced the pully wheel that turns the belt & dryer motor & put back together. The dryer now runs like a new one. Has no noise when running.

Once I watched a YouTube video showing me how to do the job I ordered the part from you. Am so impressed with your fast shipping and best prices via the Internet. Thank you SO much! The water level switch was easy to install, it ws getting the cover on the washer back on that was hard for me since I am 68 yrs old and have a bad knee. Its why it took me two hours to do what most people could do in 20 minutes.

parts were for a dryer that would not tumble or heat they did not fix problem have called in pro hope he can fix

Removed back cover,top,lower and upper front,and drum. Cleaned dust and dirt drom all of the removed parts and then removed the "lint tube". Took the tube apart to clean out dirt and lint, cleaned the lint off of the motor and blower wheel, and then removed the support wheels. Installed the "lint tube" and then the new support wheels with the new locks and then installed the new belt onto the drum. I had to support the drum in order to correctly line up the belt, and then installed the upper front panel. plugged in the power cord and started the motor to be sure everything was OK before closing up the rest of the cabinet. All was OK and the belt tracted perfectly. Installed the lower front panel, top, and the rear panel. Installed the gas connection, checked for gas leaks and installed the dryer back in place. checked operation with a batch of wet clothes and the dryer worked "better than new"!!! The instruction sheet was "spot on" for clarity and accuracy.

Ordered the fuse first hoping it was just that simple, watched the video for how to replace, first step was to take the back of the dryer off, well I order to take the back off I had to take off the Electrical Cord, as well as he top of the dryer. Only to find out he part I was replacing was not back there. Found the tech sheet attached within he dryer though, and as it turns out only needed to take he front bottom panel off. Without testing he continuity I was just giving this a shot, the Thermal fuse did no fix it, so I tried the high Limit Thermostat and Fuse kit still no luck. Took out the Element to find I was physically cracked in 2 pieces, replaced that and I was back up and running. And all parts were found in the bottom front panel of the dryer, so beware before you watch the video and take our whole dryer apart like I did.

Found right parts for problem on this website. Handyman took down machine and installed the drum support wheels. Taking apart was not too difficult; getting drum and dryer face aligned properly was a bit difficult and took longer than expected (and 3 of us). However, it was much better than having to buy a new dryer, since there was very little really wrong with this one. BTW, it was "out of warranty" so it would have cost around $150-$250 to repair using the repair service from the retailer we bought it from. Saved lots of money. Thanks.

I tore down the dryer, to find any and all issues. The belt was worn, the rear support wheels were worn, the Blower Wheel was cracked and busted, the left felt support was absent, the right felt support was shot, the water tube leading to the steaming chamber was split in two and disconnected. Ordered all parts from here, they shipped VERY fast, and the hardest part is getting the drum back in and set right. The belt was fairly 3easy to put back on if you removed the water tube support and get your right hand all the way back in there so you can pull the pulley wheel back while holding the belt. Completely cleaned the cabinet out, vacuum and scraper. Put a new exhaust hose on while I was at it, just in case. Once everything was put back together, carefully, the dryer works as good as new. I was told to never get rid of this dryer, they quit making them, and I see why. Easy to repair, does my dress clothes in the top cabinet, dries like a commercial machine in the lower. Oh some installation notes...The front panel comes completely off, if you disconnect the ground and the yellow wire on the lower right (your right) side. This makes everything else much easier. There are 4 front panel screws, 4 edge screws, and four counter screws inside the upper cabinet that must be removed. I had to pull the side holder screws to removed the top plat so I could remove the drum. Keep track of your screws!!! You will need a flathead, a Phillips, a small socket (I forget what size), and some needle nose pliers to remove clips (from the wheel).

1. Disconnect power cord and remove flexible duct. 2. Tilt dryer back and lean against wall, using folded towel to prevent wall damage. 3. Remove front/bottom panel - 4 screws on front/bottom of dryer. 4. Make alignment marks on internal vent duct where it attaches to vent bottom duct housing. Remove internal vent duct screw (towards front/top of duct) and slide vent duct out back of dryer (duct has to be removed to remove back panel) 5. Remove top panel (4 screws on back/top). 6. Remove AC power terminal block from back panel, disconnecting wire that restricts free movement of terminal block. Remove power cord from terminal block (3 nuts). Remove back panel (many screws). 7. From rear of dryer, gain access to idler pulley spring arm. Carefully note how belt routes around motor pulley and idler pulley (maybe record an image). Release belt from idler pulley. 8. Remove idler pulley triangle retainer (if still on pulley shaft) and remove old pulley. 9. Thoroughly vacuum lint and dust from all areas of dryer, internal duct, flexible duct and duct in wall (as far as possible) while dryer is in disassembled state. 10. Thoroughly clean idler pulley shaft of deposits with cloth. If desired, add very small amount of Park Tools Polylube 1000 to the cleaned shaft. 11. Install new washer, idler pulley and triangle retainer to shaft. 12. Re-route belt around pulley in original orientation. 13. Reassemble rear panel to dryer, terminal block to rear panel, and power cable and internal wire to terminal block. 14. Reassemble top cover to dryer. 15. Insert internal duct back into front vent duct, aligning guide marks, and secure with the one screw. 16. Plug unit in and briefly test, then unplug. 17. Again, tilt dryer against wall and reinstall front/bottom panel and screws. 18. Install flexible duct, plug in power cord and position unit for operation.

My way of replacing the pulley was much faster than the parts select video that showed how to replace the belt tension-er pulley. They took off the door, the entire front AND the drum to get to the pulley. I ACCESSED THE PULLEY BY REMOVING THE 4 INCH EXHAUST PIPE, (ONE SCREW) WHICH GAVE MORE THAN ENOUGH OPENING TO REPLACE THE NEARBY PULLEY! I suggest you remake that video

Repair was as straightforward and simple as the videos implied. The most difficult part of the repair was disconnecting the door wiring. It could be more plainly shown in the videos. After that it was simple. The cleanup inside the dryer, lint, etc., took as long as the repairs. An extra set of hands to hold the drum in place while routing the new belt over the drive pulley would have made it even simpler. Runs like a new dryer now.