11061632610 Kenmore Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- DANIEL from FOND DU LAC, WI
- Parts Used:
- W10837240
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Socket set
Loud squeaky sound at start up
Pulled the back panel off with nut driver , reached in removed belt from pulley , disconnected the spring , removed the the 1 bolt holding the bracket .
Put the new one in , in reverse order . Very simple , maybe 15 minutes total . While back is off , shop vac out any lint !!
Put the new one in , in reverse order . Very simple , maybe 15 minutes total . While back is off , shop vac out any lint !!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- tiffaney from QUAKER CITY, OH
- Parts Used:
- 4392067
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Belt pulley bad.
Followed the instructions on your video.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ernie from AVONDALE, AZ
- Parts Used:
- 279640
- Difficulty Level:
- Easy
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
First squeaking, then something happened and would not run.
Removed back panel to get to inside. Removed drum etc to replace drum rollers (ordered repair kit also), replaced the idler pulley etc, now like new. Repair successful!!!! Thank you!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brad from Wausau, WI
- Parts Used:
- WP8577274
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Gas dryer shut off mid cycle in timed cycle mode
Removed the lower front cover of the dryer. Removed the lint filter and removed the cover from the air duct by removing two 1/4" bolts. Removed the two 1/4" bolts retaining the thermistor. Installed the new thermistor and covers.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Howard from Boynton Beach, FL
- Parts Used:
- 350930
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Both outside door handles turned very beige
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Shea from Muncie, IN
- Parts Used:
- 279973
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Dryer not heating
Replaced with parts orded worked fine for2 hours and quit heating again
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from Mertztown, PA
- Parts Used:
- 4392067
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Squeak and Rachet type noise
The videos really make it easy. I put my laptop on the washer next to my dryer and proceeded step by step. I also found the video that mentioned about the screws that may come loose on the baffles. I found several loose screws on the baffles which I tightened and I also found the Drum hole plug loose, so I also tightened the plug. Reassembled the unit and has been working like new since.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lynn from Huntsville, AL
- Parts Used:
- WP8577274
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
no heat in dryer
diognostic suggested thermal fuse or thermistor. Thermistor tested low resistance (<2K olms). Replaced thermistor and dryer heat returned.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dan from Walkerton, IN
- Parts Used:
- 4392067
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Dryer was noisy. Rumbled and squeaked as tub went around.
I highly recommend the videos on this site for repair information. It wasn't exact for the age/model of my dryer but very close. Remove the top panel and then the control panel. Remove the lower front panel and finally the door and main front panel. Unloop the belt from the motor and remove the drum. I found one of the drum rollers was bad, which was causing my problem, but I replace all 4 rollers, the belt, and the idler wheel. Sounds like it did when it was new! Find the video for your model and watch it!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jack from Gilbertsville, PA
- Parts Used:
- WP8577274
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Socket set
Dryer shutting down two to five min. into cycle E- 1
Removed the front lower skirt with two 1/4"hex screws. Vaccumed all inner parts exposed. Removed three 1/4" screws holding the blower housing.Memoved the bias thermister again two 1/4" screws. Make sure all inner exaust pipes and rear chimney gas or electric are clean and lint free. Re assemble and test the unit. Install the skirt and make sure the dryer is level Jack, Pa.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from Redmond, WA
- Parts Used:
- 279640
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Loud sqeaks, noise during drying.
UNPLUG UNIT FIRST!!! Removed back cover. Make sure to note not all screws hold the back cover by closely observing the screw. Take a picture of the belt routing before removing from the idler pulley. Use headlamp or flashlight to light up pulley area. Remove belt from idler pulley by pushing idler assembly towards the right. Use small screwdriver to remove the existing pulley by prying off the existing tri-ring from the back of the pulley. You may have to "feel" the ring since it in facing away from you. Once tri-ring is removed, slide off old pulley and gasket or old second tri-ring. Replace with gasket first, then pulley then tri-ring. Reroute belt. Use picture if needed. Replace back cover.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Indian land, SC
- Parts Used:
- WP8577274
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Dryer was throwing a E1 Error
Took the back dryer cover off and removed the lint cover all from the back of the dryer then replaces the Thermistor (held with 2 screws).
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Katherine from Bay Minette, AL
- Parts Used:
- 279640
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Belt Pulley
The repair went great . Thanks for the part ,will be purchasing parts from you now on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- nathan from buckhead, GA
- Parts Used:
- 279973
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
thermal cot off went bad
Called a appliance place. They said it was a serious problem with master board and it was gonna cost 425.00 dollars. NO THANKS. Ten minutes to open ten minutes to find the problem. ( which was no were near the master board). Seconds to find and order the parts on partselect.com. got it next day. 15 to 30 minutes later my dryers running like it was brand new! Love it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Betsy from Round Mountain, TX
- Parts Used:
- WP8577274
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
dryer quit before clothes were dry except on the extra low setting. I got an E1 error reading
flipped THE BREAKER (very important!). Removed the cover on the bottom of the dryer (2 screws), made easier because dryer is stacked on top of washer. Removed the heater box (3 screws). Thermistor located on top of the blower housing (right side). removed old thermistor (2 screws) and unplugged the wires. Plugged the wires into new thermistor, installed the thermistor, replaced the heater box, then tested the dryer. It seemed to work fine. Replaced the cover. It has worked fine ever since.
Was this instruction helpful to you?
Thank you for voting!