11084722402 Kenmore Dryer - Instructions

Popped out the old lent trap & popped in the new one..and walla perfect repair..

remove the front panel, belt [notice the way the belt is fasten] remove the tub, support bracket to the drum roller, and slide the new drum roller on and place the tre ring in the slot. then re-install everything in reverse

Found that when the dryer continued to run after the door was opened that the door switch had gone bad. I unpluged the Dryer, opened the top of the dryer to get access to the switch by lifting top up with fingers and a gentle prying of a flat screwdriver to release spring clips holding it down. I then unplugged the wires from the switch and removed the 2 screws that held the switch in. Then reverse this process when you get your new switch from part select (which we received in 2 days) and the total time to fix it took aprox. 10-15 min. total to do. Easy fix for ANY handy person at home!

Take out 2 philips screws in lint trap holder on top. Use flat screwdriver to pry up front left and right of dryer top near outside edges and tilt up out of the way. Remove 2 push-on AC connectors on door switch and remove plastic clip holding wires to dryer's front top metal edge. Remove (2) 5/16" sheet metal screw on inside top left and right edges to free up front panel. Lift front panel about an inch and it'll then pull off. It helps to have a second person to help hold or remove the drum at this point. It took 3 times for me to guess right on the squeak. First time I replaced the belt, second time I replaced these rollers, third and final time I replaced the idler pulley, the shaft of which had worn completely off so clearly i can't figure out how we didn't see (or hear) it the first two times! Dri-Slide lube helped stop the squeaking the first two times, but it always returned until this time, now I have a thoroughly rebuilt dryer for the next generation! (PS vacuum out the bottom of the dryer while it's open to remove both lint and greasy roller shavings - do this FIRST and you'll have cleaner hands & clothes!)

I followed the instructions on the video and it was simple. The hardest part was vacuuming out 32 years of lint from around the motor and igniter. I was lucky there was never a fire in the dryer.

The videos showed the tech taking the front off the unit but my unit didn't play that game. Instead all I had to do was take the top loose, (don't forget to take the dryer vent screws out first, that was the first beer) then access to the switch was easypeezy. That coupling for the switch assembly was 2 beers long. Anyways, got it all back together and it works like it's suppose to.

my hany man did it....

Excellent and super easy. Owned the box and snapped the new one in. Ready for laundry again in a matter of minutes.

Didn't need a repairman for this project! Ordered the part (seems like on Sunday) and got it really quick (the next Wednesday). Opened the package, placed the part where it was supposed to go and shazam!!!! Fixed it was quick and easy!

Removed door gasket that was on the door. Replaced with newer gasket (was a tad bit too big, so it slipped off as well.) Added some electrical tape to hold it on. Works like a charm.

I would not ever consider this a repair. The dryer filter cracked because of my wife put it in loosely. The new one just fit right in.
What was so good about the entire process was how quickly I recieved the part. A matter of two days.

Watched a you tube video that told me exactly how to do it. Saved us from going out and buying a new one. My husband and I were very proud of ourselves because just to get someone to look at it would have cost us $85. The part was only around $25.

Replacement fit perfectly.

Easy for a 87 year old.I just snapped the cover to the filter basket and then inserted the whole basket into the

1. Popped off hinged dryer lid at front and supported to allow access to lint chute
2. Removed back sheet metal panel
3. Removed dryer chute to expose sensor; removed same-deformed terminal on top needs to be straightened with pliers to remove through slot.
4. Installed new sensor; terminal needs to be twisted to ensure solid installation and good ground. Bottom pops in but took a bit of finagling.

Accessing and replacing the sensor was straightforward enough; bulk of the job was cleaning off old gasket material (severely degraded) in two locations. Used plastic scraper and razor blade scraper, then cleaned sticky with goo gone. Installed new gasket strip from Home Depot; available in rolls. I used 1/4" x 3/8". Surprising how much lint/hair/debris was in bottom of lint chute. Glad to get it all clean.