11067022710 Kenmore Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Gregg from St. Augustine, FL
- Parts Used:
- 279570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dryer door would not stay closed
After removing front door panel (2 screws) I removed the old latch catch and replace with the new part. 4 minutes later, the door was back together, the dryer was running and the door was staying closed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Glen from Covington, LA
- Parts Used:
- WP3392519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
timer runs but dryer wont start (fuse was not closed)
Took off the backplate of dryer, replaced fuse, done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DONNA from SAN LORENZO, CA
- Parts Used:
- 279570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
catch was missing to close dryer door
The only thing I had to do was hammer the catch inside the square fitting and presto it was done. It took me less than 3 mins. I thought I might of needed instructions, but it was really simple. Even a guy can do it. (smile)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeff from Moberly, MO
- Parts Used:
- WP3392519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Dryer just quit
Took back panel off dryer, unscrewed old part, put on new one. Easy fix. Dryer works great again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from Union Beach, NJ
- Parts Used:
- 279570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The door whould not close enough for the dryer to work.
Got my parts very quickly.
Popped out the old door latch with a screw driver and pressed in the new one.
Very simple.
Thanks Parts Select.
Popped out the old door latch with a screw driver and pressed in the new one.
Very simple.
Thanks Parts Select.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rick from Benicia, CA
- Parts Used:
- WP3392519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
The dryer blew only cold air
I opened the front lower cover to get the schematics. Looked for the most probable part that was bad. Then traced wiring from the gas solenoid to find the thermal fuse.
I opened the back. Took the two wires off the thermal fuse and put my Ohm meter from terminal to terminal. As I got no reading, I ordered a new fuse. It took about 5 minutes to replace and button the dryer back up. This is the second time I have had to replace this fuse.
I opened the back. Took the two wires off the thermal fuse and put my Ohm meter from terminal to terminal. As I got no reading, I ordered a new fuse. It took about 5 minutes to replace and button the dryer back up. This is the second time I have had to replace this fuse.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Diana from Canfield, OH
- Parts Used:
- 279570
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
dryer door won't stay shut
I replaced the male end first hoping that a change in the female part would not be needed. Unfortunately no. I used needle nosed pliers to pry the male part out and pushed the new part in. The female part of the door catch was more difficult. I didn't do it in "textbook" form, but got the job done with pliers and a screwdriver. Worth every penny to fix correctly instead of rigging it. Do it!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from SCOTTSDALE, AZ
- Parts Used:
- W10120998
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- Less than 15 mins
Torn filter seal
Remove old filter, throw it away, replace with new filter.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Terrell from Chicago, IL
- Parts Used:
- WP3392519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
No heat power was good
Unplug dryer from out let remove rear panel remove the two wires located on the fuse remove faulty fuse installed new fuse replace rear panel and exhaust tube
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from UPPR MARLBORO, MD
- Parts Used:
- 279570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Broken dryer door catch
Followed the video instructions which were comprehensive, easily understood, and prefaced with a listing of necessary tools. Completely satisfied with parts and supplementary information.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from NORTH EASTON, MA
- Parts Used:
- 279570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Door would not stay closed - so dryer kept shutting off
Followed Youtube video - quick & easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anthony from LEXINGTON, TN
- Parts Used:
- WP3392519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Changed out timer on Admiral dryer
Very easy, part fixed the drying issue! Unplug dryer, slide dryer out to access top rear panel and remove the 1/4'' nuts, unplug the 3 plugs connected to the timer along with the 2 screws
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karolyn from FREDERICKSBRG, VA
- Parts Used:
- WP3392519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Dreyer overheated and stopped working midcycle
Very simple repair, and we're not handy at all. I cleaned out the dryer lint with a vacuum. Then we watched the partselect video on how to replace a thermal fuse. Husband used a nutdriver to take off the back panel. He took out the old fuse, put the new one in, crewed the panel back on. Voila!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- james petrie from Stoughton, WI
- Parts Used:
- WP3392519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
no heat in the dryer
after removing the back panel (5 screws) i replaced the heating element, (about 15 minutes, after vacuuming all of the lint and dog hair), replaced the panel, but still no heat. removed the back panel again, and replaced the thermal fuse. (2 screws, 5 min.) still no heat, so on to the thermostats. (there are 2, both in easy reach). i replaced the one in the heating element housing first, as this made sense. (it has a red stripe across it, so they can't be confused), replaced one connector, which the new part requires, buttoned it up, and presto!! the dryer works just as new! all told, i have less than 100.00 with all of the new parts. the longest part of the whole thing was cleaning all the lint and debris out first, which you absolutely must do
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Orem, UT
- Parts Used:
- WP3392519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Dryer wouldn't heat but would blow air
The major issue was getting the dryer out and cleaning it all up. That's what took the time but it was worth it to clean out the lint in the ducts, etc.. Putting the thermal fuse was a snap thanks to the great feedback received when I got this web site and read the previous responses.
Was this instruction helpful to you?
Thank you for voting!