11075132410 Kenmore Dryer - Instructions

My Whirlpool dryer had no heat. I removed the back panel and within minutes diagnosed the problem to a blown thermal cut-off fuse. I ordered a thermal cut-off kit on a Sunday night and had the parts at 7:30am Wednesday morning. Total time for diagnosing and repair was no more than 15 minutes. PartSelect saved me a ton of money and aggravation!!! AWESOME!!!!

Gary

Took of the back cover, and removed the vent connecting the blower motor to the drum. It was completly full of lint, so cleaned it out completly, and tried the dryer again. The heater element was still cutting off early, and the clothes were not getting very warm, but better than before. Decided to change the thermal cut-off switches. Ordered the parts on Sun, they came in on Tuesday. Dryer was up and running Tuesday night. Just 2 screws per switch, took less than 1/2 hour. The dryer now runs like brand new, and my wife was ready to fork over $800 for a new one!

First I did a search on dryer repair. Found a website that described easy things to check with an ohm-meter. I then performed the continuity checks on the items and found the high-limit one was open, in other words, no good. It works similar to a fuse. All this was done after removing the back panel, just a few screws. The reason it exceeded the high limit, possibly because I never opened the back up and cleaned it. Found out it should be done every couple years. My vent line had a hole in it and was letting lint get drawn into the heating element, could have been a fire.

Sensor is in the front lower left. Gas off, electicity off. Removed two screws for the filter, pry/lifted the top up and taped it too the overhead cabinet, removed two screws inside top of front panel, lifted pandel with door closed staight off. Two screws to remove the flame sensor braket. unplug the old sensor install the new one and reverse everything. With others suggestions I purchased temperature switches etc. but the radiant flame sensor was the problem. I now have some spare switches for future. Excellent company and very quick service. Oh, Sears wanted 200.00 just for the service call, I live rural.

removed frt & rear panels & drum and lint chute for seal replacement replaced these components, problem didn't go away, ordered & replaced both gas valve coils (m series coil kit) problem solved

The repair was fairly straight-forward. I removed the front of the dryer, lifted the top off, and then released the tension off the belt dy depressing the pulley arm. Once the belt was off, the drum came right out and then it was on to unhooking the wiring from the old motor. Very simple up till this point. The snag came when I went to unthread the impeller fan off of the old motor shaft. It was permanently sealed onto the shaft so I had to cut the old shaft into using a reciprocating saw was a metal-cutting blade. Once this was done the new motor installed easily exactly like the old one was mounted. I had to also purchase a new fan due to the fact that I was unable to remove the cut shaft from the old fan. All parts worked great and the dryer assembled back together easily. Works like a new dryer now.

Was not sure what was wrong but the Part Select site allowed us to view other repair issues and solutions. We ordered the kit, it arrived the next day (how is that possible) and easily put the parts in and chaching...money saved and dryer works better than ever. THANKS PartSelect, we give you an eleven and we will recommend you to everyone.

I have not received the parts yet waiting on the motor, can’t put the blower fan in without the motor, ordered it , Jan 23rd, still no motor, have to go to laundry mat, have you ever had to do that with 7kids, and you and your wife’s laundry, probably not, because you would have had your motor by now. Maybe you can help me with the part so I can redo a testimonial here for you. 19 days and still waiting

Be very careful of burrs on the edges of the steel inside the dryer. I cut myself badly when reaching into unplug the switch.
Procedure: Lifted the dryer top by pulling forward and rotating front up. Removed 2 philips screws holding the switch at the door. Reached into dryer and unplugged bad switch. Inserting small blade screw driver at the edge helped release the plugs detent. Installed new switch using reverse of above.

First i removed the rear panel on the dryer.the removed bothe thermostats that were on the blower housings.unpluged all wiers and installed new thermostats.reinstalled the wiers in there proper locations...note to log the location of the wires when removing from old switch.reinstalled the rear panel and hooked dryer back up and test.

The first thing I did was call my friend Donnie who manages some apartment buildings and who is always complaining about fixing things and getting the right parts to fix things. He told me what to order from PartsSelect and when the parts got here I called him up and he did the repair work.

He was reluctant to do the work at first but after he found out I had ordered the parts from PartsSelect he was happy to do the work. "Their parts are always right and they always work," was what he said after he had my dryer working just like new. So if you know nothing about fixing things and buying parts just call PartsSelect and you will be fine. Just ask my friend Donnie!!!

Actually, I was the handy man. First I removed the front panel. Then I used 3 - 2x4s to hold up the drum. Then I slipped the belt around the center of the drum ,motor,and around the pulley at the bottom of the dryer. That was it, and then I put it back together. My wife was amazed and proud that I did it without calling for help! No Problem!

Step one: UNPLUG THE 220V LINE!
Removed the 2 screws on top under the lint door then flipped up the top. Next I unclipped the wire harness at the front and disconnected the 2 wires to the door switch and flipped the harness out of the way. Then I popped off the kick panel. Next, I removed the (4) 9mm screws holding the front panel on. The 2 lower screws only need to be loosened and the panel lifted off. Note the location of the door springs at the bottom. These springs can be reinstalled easily through the kick panel after you reinstall the front panel.
Next I removed the remnants of the old seal from the front panel but left the 3 plastic clips in place. The seal wraps around the perimeter of the panel and is held in place by the lip of the opening. The extra flap is then folded back so that the folded edge is toward the dryer drum and away from the front of the panel. The sketch in the instructions is not helpful!
Next, reinstall the front panel. As you set it onto the lower screws, you may need to lift the drum slightly to fit the panel into the drum opening. Tighten the 4 screws then reattach the 2 door springs. Test the operation by turning the drum counterclockwise by hand. Check to make sure the rear seal has not been displaced or damaged. That seal is actually glued into place. If it turns smoothly, snap the kick panel back on and reinstall the wire harness. Flip down the top and reinstall the 2 screws at the lint tray on top. Plug it in and give it a spin!.
Note, While you have it open, you'll want to use your shop vac and clean all the lint and pocket change out of the machine. You might as well take off the back panel and clean up in there and in the vent pipe too.
I didn't know if I needed a new belt but ordered one anyway. The old one turned out to be pretty well shot. After I had the front panel removed, replacing the belt is very simple. There is an idler pulley underneath that is under tension. Just push on the idler until the belt is loose. Switch the new one into place and you are done.

romoved from pkg. and fit it to the door. no tools needed. best of all the part came in 24 hrs and was fixed with out delay of waiting from a store that was out of our area. great costumer service!!!!!

Asking my question on you tube they show me problems and parts to need replace and how do installation.