11076132412 Kenmore Dryer - Instructions

Gently remove the door bezel by prying it off with a small screwdriver. Then remove the door catch from the door with the same screwdriver. Be careful not to drop it in the door. I did and had to fish it out with a small hooked pick. Install the new door catch by sliding the top in first then the bottom. Again, careful not to drop it in the door. Then snap the door bezel back in place.

Once I received the new latch I removed the latch cover with the flat head screw driver and worked out the old latch. I then positioned the new latch and snapped in place. I then replaced the cover and shut the Dryer door. The door latched and the repair was complete.

I pushed one end of the catch on upper side the hole and when locked, I pushed the other end of the catch to the lower side to get locked. To complete, the white cover was inserted on top of the catch and done.

took out old ,twisted in the new one it was nice to have the right part the first time!! thank-you

Remove the protective cover on door with screwdriver, pop out the old catch, snap new catch in place, replace protective cover

Replaced door catch on dryer door. Followed video on Whirlpool website and it took less than 10 minutes. The dryer works great.

Remove the lint screen, then remove the two (2) Phillips screws that are at the entrance of the lint screen compartment. Take a putty knife and insert it under the top pannel of the dryer about 1” in from the outside and push the putty knife in as you lift that corner of the pannel. Repeat on the other side. Then raise the lid and prop it up. The door switch is on the right side just behind the door on the inside. Open the door and remove the two screws that hold the switch and remove the switch. Install the new switch like the old one came out and close it up you’re ready to go! It is very easy you can’t hurt anything.

I just followed the instructions from this site for the door switch part and had it running in 10 minuets. This site made it very easy.

First unplug appliance, Remove dryer top and front. remove drum and belt. Two clamps hold motor in place. remove them and lint chute housing in rear, exposing the fan. Use vice grips to hold motor shaft behind belt pulley flat spot. Remove fan, it's reverse threads. A large adjustable wrench on plastic fan nut and spray lubricant if very tight. Place new motor next to old and switch wires over, crimp on new 1/8'' connectors. Remember the green ground wire may need an allen wrench. Put back drum,belt, lube the rollers and replace back cover, front, top.

Had to replace the rear felt seal and the motor. It was no problem to find videos on how to do both of these repairs. Took apart the appliance. When the parts came first replaced the drum rear felt seal and waited for the motor to be delivered. Then replaced the motor as per online instructions. Also went to Home Depot to buy a new flexible dryer tube since the old one had a few holes. It works perfectly again.

follower the instructions from a you tube vid on whirlpool dryers. The connection of the motor to the blower is fairly tight be sure to turn it the correct direction, retaining clips for the motor are harder than is looks to reinstall. The new belt and rollers were a prenventive measure, If I had it apart I should just install the new belt and rollers.

There are many good youtube Kenmore/Whirlpool door switch replacement demos online. The one already done by this site )was close enough for me. I could see that the door switch on my dryer was bad (the plastic part that the door makes contact with was visibly broken, as seen from the outside) -- so I ordered a new one. You don't have to open the top fully to access the switch wiring harness -- i propped it open with a roll of duct tape, The hardest part for me was to disconnect the old switch from the harness (I used a small flat bladed screwdriver to free it). Be careful, the metal inside the opened dryer is sharp, and can cut you.

pulled dryer away from wall took screws out of lint screen lift top removed 2 screws one on each side of front at top and removed front panel. pulled belt off drum removed drum rollers tension pulley and while i was at it pulled back cover off of heating element and blower blew everything out with air hose did a total cleaning installed everything in reverse. i was amazed how fast the parts came the dryer was only down 2 days and it runs like new even if it is 20 years old i highly recommend parts slect and i will use them in the future

Noticed the door switch was loose and the light bulb inside dryer didn't stay on. Researched the problem on PartSelect. Followed the directions given: Take 2 screws out of top of lint trap. Pry top off of dryer with putty knife. Unscrew 2 screws in dryer door frame holding in old switch. Uplug and remove old switch. Plug in new switch and put screws back in. Close top of dryer. Reinsert 2 screws in lint trap. My 20 yearn old dryer works!

This could not have been easier. The hardest part was tipping the dryer over on its' side.
Instructions:
1. Tip dryer over onto a non-scratch surface. I used a tarp on the floor.
Insert leveling foot into the foot opening on the bottom of the dryer &
screw in with fingers until it is difficult to turn.
2. Use the adjustable wrench on the hexed foot (not the threads) to adjust to the desired level.
3. Tip dryer upright taking care not to exert pressure on the feet closest to floor. I used a folded-up tarp under the bottom edge of the dryer while lifting it to the upright position.
4. Use a level, back to front & side to side, to determine if feet need further adjustment.
5. Adjustments can be made with the dryer in the upright position, using the adjustable wrench on the hexed foot.