11062102311 Kenmore Dryer - Instructions

Kill power to dryer from breaker box.Remove lint filter & 2 screws. Take a flat head screw driver and place in gap between rash from corner of top panel & front panel of dryer and pry up to raise top panel of dryer & rest against wall the wall on angle do it doesn’t fall back toward you. Unplug wiring harness from dryer switch inside top front corner of dryer with outside of drum exposed when top panel of dryer is raised. Open dryer door and remove screws on each side of dryer switch located at upper inside corner of door opening. Take flat head screwdriver had slide in between connector & wiring harness on dryer. Remove old switch. Reconnect new dryer switch to wiring harness & remount switch to inside of dryer door opening. Lower top panel of dryer & press front corners of top panel to front panel of dryer & clips will be locked in place. Replace screws in dryer filter mounting holes yo top panel & replace dryer filter in place. Turn on power ‘ & check if light is working 1st. Then, turn timer knob clockwise, close door and listen if the drum is turning. Open door to see if drum turns. If both work, the job is complete.

OPENED REAR OF DRYER TOP PANEL, TESTED FOR CONTINUITY ON TIMER, ALL TEMP SENSORS AND HEATER COIL WITH MULTI-MEETER AS DESCRIBED IN ONLINE YOUTUBE VIDEO FOR WHIRLPOOL DRYERS. TIMER TESTED BAD AND REPLACED TIMER. EASY TO UNSCREW AND UNPLUG.

The original door catch had broken and would no longer stay shut. Ordered the part from this site with ease. Very easy to replace the broken door catch on my Amana dryer. Tool needed was a flat head screwdriver to loosen the cover, remove broken piece and easily replace with new part. Followed the video and it was back to normal operation within minutes.

10 min. job, easy to do / two screws top and two inside front / remove old parts install new.

Took the old one out, replaced it with new one.

I opted to remove front, top and back panels. This is best done with dryer laying on it's back so drum remains in position. Hold panels and pieces in place with masking tape (2") You should block up the dryer so you don't damage the gas pipe. I opted to total shop vac out the piece and lubricate the rollers and tension pulley. I made more in change than the belt cost!

Overall an easy repair. Belt came with diagram for easy threading the belt.

I am a teacher and teaching is my game. I have always, with my four children, taught them to do mechanical work themselves. I and most of my children have a PhD, but in having said that, I confess, we come from a very mechanically talented family. It shows and proves to be of great benefit.
OK, so much for the intro.

I gave my daughter the tools and said, "What do you think is wrong with the dryer and where would you start?" She tested it and said, "The motor is running, but the tub is not turning thus I conclude it is the belt because I can hear the motor running eliminating that as a cause.

She then opened the top, looked around and removed two screws from the lint catcher. She looked it over, looked a me, I shrugged my shoulders and she then took a rubber hammer and popped the top off. Don't ask me how she knew that, but I think she saw the rubber pins through the crack between the case and top. She raised the top after removing two screws in back to relieve the simple hinge and also disconnected the wiring clip and sure enough, the broken belt was inside the cabinet. We called you, the best, fastest and most accurate service on the Internet and ordered a replacement. I would like to add, the price is always more than fair and delivery very prompt.

When the part came, my daughter took it up to our laundry room and within twenty minutes, she tested it and everything was fine. She did smell a little burning smell which might be attributed to a new belt or the fact that there was no clothing in the dryer.
Thank you so very much.
Dr Robert E McGinnis

Opened up every panel EXCEPT the front, then discovered how easy that is. Replacement belt was a snap to install. I noticed some plastic collar thing on the driveshaft appeared to have melted. Did not appear to be critical part, so I put it together and tested it out. Seems to work fine. I think the collar is there to prevent the belt from potentially slipping off the driveshaft.

My son did the repair and said it was so easy!

Removed top cover. Removed front cover. Removed Drum. Located the broken belt. Found that there was no tensioner in the unit. Replaced drum rollers. Put in new tensioner. Repaced Drum with belt around it. Installed belt through tensioner and onto drive pully of motor. Supported Drum with wood block. Turned on dryer to insure drum turned without any problems. Removed wood block. Replaced front cover and top cover. Repair compete.

He had to put it flat on one side in order to put the legs on it.

Removed old door switch and tested with ohms meter. It registered as charged, but when black button was pushed it did not cut off (go to zero). Replaced the part just like the video showed. Only problem i had was dropping my screwdriver down into the dryer well. It was doing no harm so i left it there since i tried retrieving from the back but was not able to get entire back off!

First removed lint screen, then removed screws holding lint screen housing.Pushed on back of machine a little so that top could be pried up. Then replaced switch and put everything back together. Helps to have two people so one can push on back of top piece while top of machine is being pried up.

I just followed your video how to replace a broken belt , after viewing replacing belt went easy

follower the instructions from a you tube vid on whirlpool dryers. The connection of the motor to the blower is fairly tight be sure to turn it the correct direction, retaining clips for the motor are harder than is looks to reinstall. The new belt and rollers were a prenventive measure, If I had it apart I should just install the new belt and rollers.