11062332511 Kenmore Dryer - Instructions

Unplugged Dryer.

Removed back panel & dryer hose - About 10 screws

Removed Heating element - two screws

Followed instructions for replacing old thermal cut-off with new model (this was slightly different from original equipment - wiring modification was required) All connections were detailed in the instructions. Jumper wire and new screws included in Thermal Cut-Off kit.

Cleaned lint and dust from inside dryer.

Replaced back panel and dryer hose.

Tested dryer, works like new.

Pulled the dryer out from the wall and laid it on its front on a blanket.Removed the back panel.Disconected the two switches and replaced them with the new ones.Cleaned up dryer replaced back panel and returmed the dryer to its original place and she works just fine.

Used the trouble shooting tips provided as a guide and a multimeter to test and find the defective part. Testing indicated no continuity thru the high limit thermostat. I ordered the part and received it in 3 days. Had the repair done a full week before the repairman could even come to the house and saved well over $100 in repair costs and 2 weeks or longer of down time. Great website and service.

Watched the videos available. Opened the top and saw tub jumping. Unplugged and removed front panel. Saw tub rollers were broken or melted. Removed tub watched more videos, and installed the felt belt I got from PartsSelect. Trouble removing the tub rollers, but finally got them off. The axles had a sticky residue which I removed with 220 grit sandpaper. I installed new rollers I had bought locally. Reassembled dryer. Worked quietly and smoothly, and it no longer shut itself down. Worked well for one day when it started.s loud noise with bumping. I found both rollers had lost their outer rim , and the tub was running on hard plastic and there was sticky residue back on the ankles. I stopped there.

Researched causes of low heat and purchased thermostat and heating element. Delivery was less than one week. Installation was easy with the on-line video.

put the high limit in , plus the temperature , plus the exhaust switches

Turn off the breaker to the unit or unplug. Disconnect the 3 wires, 2 hex screws keep the element in place. it swivels or slides out. keep the thermal fuse from the old unit, it disconnects from the spade lug and pops off.

I made sure dryer was unplugged and I removed back to expose the heating element canal on lower right side. Removed two screws and two electical connections. Pulled the element down and out. Used a flathead screwdriver to slowly pry the thermo senor off the heating element assy. There are no screws here just a small metal piece to hold it in place. Discarded the old element and reversed the above procedure. The best part of this is the part arrived quickly and I saved $50-75.

Replaced roller. Very simple. Dryer is the easiest appliance to repair. Only a few parts keep a dryer working

My wife took the back off the dryer, took 2 screws out of each side of the heating element caseing, unplugged heating element. Plugged in new element, put caseing back in place replaced 2 screws, put dryer cover back on, finished. Works great again.

I followed disassembly directions found on youtube and replaced th two-piece ring bearing that was identified by a parts diagra fron PartSelect. The repair was easy. Fix time was about thirty mionutes.

first i removed the back cover by removing the six 1/4 inch screws then i removed the wires to the thermal switch there were three of them and using an ohm meter i checked each one for continuity until i found the one that had an open circuit. i removed the two 1/4 inch screws holding it in place and replaced it with the new one.

after i got the replacement filter, it fit perfectly. the filter is white & my dryer is beige but i don't care...i'm just happy i have a good lint filter again, for my at least 30 year old dryer....thanks part select!

removed the back housing of the dryer and located the thermal switch. unscrewed the old one, popped in the new one and whala! I was back in business!

put the back cover back on the dryer and pushed it back into place.

Disassembled dryer, removed tumbler, replaced drum support rollers