11062332510 Kenmore Dryer - Instructions

Grown daughter did the repair following instructions on your site........Unplug, take screws out of top by lint filter and with putty knife pry up top panel and lean back. Unplug elec. harness in front corner. A screw on each side of front panel removes that. Get old belt off and then we vaccumed all the lint from under and around drum. Put new belt around drum making sure not twisted and pull pulley as shown to make tight......... would have taken less time but we vaccumed all the lint from under and around the drum. Anyone could do this......

Once we realized we needed to take the FRONT off the dryer, not the back all went well. It was an easy fix and the part fix perfectly. Instead of $60 or more for a repairman, we spent less than $20 fixing the dryer.

I changed the belt, tension pully and rollers. Runs like new now. I also took the opportunity to clean it out real good while I had it apart.

We had to pop open the top. Unscrew front of dryer from sides. Disconnecting the wires was a bit more difficult than expected. We had to use a tiny screwdriver to slide into the sides of the white wire connector on each side before pulling apart. Front drum falls when front of dryer is removed. It took two of us to reassemble - one to hold the drum while the other put the front on. Our problem turned out to be one wheel. We replaced both wheels and saved the rest of the parts. Hums along just fine.

I just followed your video how to replace a broken belt , after viewing replacing belt went easy

follower the instructions from a you tube vid on whirlpool dryers. The connection of the motor to the blower is fairly tight be sure to turn it the correct direction, retaining clips for the motor are harder than is looks to reinstall. The new belt and rollers were a prenventive measure, If I had it apart I should just install the new belt and rollers.

First removed lint screen, then removed screws holding lint screen housing.Pushed on back of machine a little so that top could be pried up. Then replaced switch and put everything back together. Helps to have two people so one can push on back of top piece while top of machine is being pried up.

watched your video on 'how to' and did it like man showed..no problem

Removed old door switch and tested with ohms meter. It registered as charged, but when black button was pushed it did not cut off (go to zero). Replaced the part just like the video showed. Only problem i had was dropping my screwdriver down into the dryer well. It was doing no harm so i left it there since i tried retrieving from the back but was not able to get entire back off!

He had to put it flat on one side in order to put the legs on it.

The part arrived in the mail. I used a pair of kitchen scissors to open the package. I removed the part from the plastic bag, and snapped it into place on the front of the dryer. Total time: 15 seconds.

I wish all my repairs were this easy.

Replaced door catch on dryer door. Followed video on Whirlpool website and it took less than 10 minutes. The dryer works great.

Once I received the new latch I removed the latch cover with the flat head screw driver and worked out the old latch. I then positioned the new latch and snapped in place. I then replaced the cover and shut the Dryer door. The door latched and the repair was complete.

Gently remove the door bezel by prying it off with a small screwdriver. Then remove the door catch from the door with the same screwdriver. Be careful not to drop it in the door. I did and had to fish it out with a small hooked pick. Install the new door catch by sliding the top in first then the bottom. Again, careful not to drop it in the door. Then snap the door bezel back in place.

Noticed the door switch was loose and the light bulb inside dryer didn't stay on. Researched the problem on PartSelect. Followed the directions given: Take 2 screws out of top of lint trap. Pry top off of dryer with putty knife. Unscrew 2 screws in dryer door frame holding in old switch. Uplug and remove old switch. Plug in new switch and put screws back in. Close top of dryer. Reinsert 2 screws in lint trap. My 20 yearn old dryer works!