11078133410 Kenmore Dryer - Instructions

Followed online video very easy and dryer works like new one....

Removed the top, removed lower front cover, removed the front, removed the belt, removed the drum and the back. Removed and replaced roller support shaft and drum roller’s. Completed all Front and rear support for drum. Replaced drum , replaced drum roller belt and replaced back, completed replacement of the top, front.

Once I received the new latch I removed the latch cover with the flat head screw driver and worked out the old latch. I then positioned the new latch and snapped in place. I then replaced the cover and shut the Dryer door. The door latched and the repair was complete.

Unplugged the Dryer first. Removed the two screws from the bottom panel using a 1/4 socket and removed the panel by pulling down and out. Reached behind the blower and removed the connectors from the old thermistor and then the thermistor itself by removing the two 1/4 inch hex head screws. Replaced with new part and after screwing back in, reconnected the wires and replaced the panel. From start to finish, it took me about 20 minutes.

Unplug unit turn off gas, remove only bottom front panel first tried radient flame sensor was not the problem it was the coils which were infront easy to acess with small screw driver remove two prong coil and replaced then the three pronged coil being sure to line them back before tigtening left off cover and watched for ignition once it turned on and ran replaced cover and done.

Unscrewed the inside part of the door from the outside door shell. Removed the broken pieces of the catch and replaced it with the new one. Screw the door back together. Did not need to remove the door from the dryer cabinet.

The hardest part was figuring out how to access the dryer mechanism. This Amana dryer has a lower front panel that is removed and not the top. There are few instructions available for this configuration. Then the part locations do not resemble the video instructions for trouble shooting. I discovered the broken part because when fiddling with the wire connections the metal tab disconnected due to fatigue or corrosion. Removing, identifying and replacing the flame sensor was quite simple. The dryer now works as before. The dryer is 23 years old. The most time in this repair was spent figuring out how to disassemble and identify a different configuration than in the videos.

I started by changing the part that had the highest percentage to solve this problem , the top three didn't work , the fourth part, the disposable thermostat, and the last one that could be done from the front worked.

Message indicated something amiss in the motor circuit. Followed Instructions in the on-board manual. Turned out to be the internal-bias thermostat, and the exhaust air thermistor both. Changed faulty parts, cleaned lint from the system and we are off and running again.
Thank You.
DW Pranger

removed broken parts & snapped in new catch

I googled the problem and determined that the thermistor was faulty. I found your web site from which I ordered the replacement part. The part arrived within a week. The replacement was not particularly difficult, but the space was very tight (without removing more panels and covers). I just kept at it and got it installed and the dryer works fine now. There are several pertinent videos on you tube, none of which were my particular model, but the combination of them led me to a successful installation.

I removed the metal piece which held the plastic "catch". There were no screws, squeeze to remove it. Then inserted the plastic part and re-inserted the metal part into the dryer door. Very simple. But even more pleasing was the easy ordering and the quick delivery of the part! Thank you so much!

I ordered the part(and a backup) and had it in two days. 5 days less than ordering from sears.

I thought it had to be the igniter so I replaced that part. The dryer still did not start. I replaced the high limit and hoorah dryer works. Two weeks go by, the dryer is drying the clothes but my wife smells gas in the laundry room. I replaced the coil pak on the gas valve. My wife says she still smells gas. I replaced the radiant flame sensor and no gas smell for 2 weeks now.

Followed your video for replacing the Tension Pulley, Drum Belt and Drum Rollers. Models were not exact, but instructions were very clear and detailed enough for a "computer geek" to do the repair myself (with some help from my wonderful wife). Live in Ohio, parts came from Kentucky and I had them the next day! The dryer is almost 10 years old. Running great now. Thank You!