11078132413 Kenmore Dryer - Instructions

removed the two screws that hold the coils in place pulled the coils terminal connections off removed and replaced with new coils reattached quick disconnect terminals dryer now works better than when it was new

I removed two wires from the coil valves. Then I removed two screws from the bracket that holds the coil valves in place. I removed the faulty coil valves and replaced them with the new ones. Put the bracket back on and replaced the two screws and wires. It took almost 5 minutes. The dryer is like new once again.

I used a socket to take of the front cover. I used a screwdriver to remove the two screws that held the coils in place. Replaced the coils and put everything backs together. Piece of cake!

we had to disassemble the dryer to get to the part in question. a friend who worked In appliance repair, checked all the connections & they were fine. He said it had to be the part I ordered. After installation it still didn't work. I called whirlpool who own Maytag. They gave me a company to call. After his inspection, he determined it was A heat sensor fuse, located in the bowels of the dryer. So I packaged up the part & returned it to you.

I unplug the electric, close the gas valve, use the putty blade to prize up the top,unplug the electric horness, took the front door off, took the anker plate off the two coils, removed the wire from each coil,be careful not toget the wires mixed up one coil has two proms and the other has three proms after that u put everything back together the way u took it off!!

The hardest part was figuring out how to access the dryer mechanism. This Amana dryer has a lower front panel that is removed and not the top. There are few instructions available for this configuration. Then the part locations do not resemble the video instructions for trouble shooting. I discovered the broken part because when fiddling with the wire connections the metal tab disconnected due to fatigue or corrosion. Removing, identifying and replacing the flame sensor was quite simple. The dryer now works as before. The dryer is 23 years old. The most time in this repair was spent figuring out how to disassemble and identify a different configuration than in the videos.

Replaced Coil kit and internal bias thermostat. Checked overheat fuse. Still not heat. R/P igniter and igniter thermostat to be sure not bad. Still no light or heat to ignitor. Pulled wires from two thermostats in series where flame comes out and found them burnt and one completely open. Repaired wire and dryer works. Had relied on various videos to get me through process. Parts were not that expensive so I don't really think a waste of money compared to calling a repair person.

Followed directions from Youtube video

Message indicated something amiss in the motor circuit. Followed Instructions in the on-board manual. Turned out to be the internal-bias thermostat, and the exhaust air thermistor both. Changed faulty parts, cleaned lint from the system and we are off and running again.
Thank You.
DW Pranger

Open top of dryer, then remove front. Coils on lower left. Unplug and replace coils. Vacuum loose lint from bottom of dryer. Replace front then top of dryer. Test run. All good !

Removed the screws on the dryer vent and the back of the dryer top. Then I raised up the top panel and removed the screws that held the front panel on. I removed the front panel to access the coils. I replaced the coils and then the front and top panel and screws. All went well. The dryer is working properly now.

Diagnose that the circuit is functioning up to the igniter. This is done by removing the peep hole cover on the bottom front panel, turn the dryer on and watch for a glowing igniter. My dryer would still ignite the first time because the coils would not show an "open" until they heated up. So if you see the igniter glow it is most likely your coils are bad. Remove two screws from lint trap area on top of dryer. Pry up on top panel at the two clips. Panel is on hinges, so flip it out of the way or just brace it with something enough to keep it off the front panel. Remove the two bolts from inside top corners of the front panel. Use a small punch or screw driver to push in on the tab to release the doors electrical connector. Pull straight up on front panel to remove it from bottom clips. The gas valve is very easy to get to without removing the drum. If needed for inspection or cleaning, just pull back on the belt tensioner to remove the belt from the motor and then pull the drum out. Or just use a stubby phillips screw driver to remove the bracket from the top of the ignition coils. Use a very small flat head screw driver to lift the locking tab on each electrical connector while removing. Remove the coils and place new ones in very same position (note the tab or key way of the coils faces up and are defined in the bracket). Re-assemble all parts making sure connections are tight and drum is correctly mounted. Note: if you remove the drum, return the belt back, in a loop, through the tensioner. This part hurt my head for a moment because I did not pay attention. Also a good idea to vacuum the debris and lint while your in there! As always check to make sure the exhaust pipe is clear. Have fun!

I started by changing the part that had the highest percentage to solve this problem , the top three didn't work , the fourth part, the disposable thermostat, and the last one that could be done from the front worked.

rts came quickly & I got started. First, I unplugged the dryer and pulled it away from the wall about a foot. this was done so the top would have clearance when it was lifted up. Next, I removed the lint trap and then took the two screws under the lint trap door out. Then you use a screwdriver(flat blade) to release the top of the dryer. The release points are about 1-2 inches from the edge of dryer. Next pull the wire connector apart so the front can be removed. The connector is on the right side, front corner, facing the dryer. There are two hexhead screws near the top on both sides. Remove the and the front will come apart as you lift it slightly. Then you disengage the tub belt. Once this is done the tub can be lifted out and set aside/ take care to remember each things position as you take it apart, so you will not get confused when you reassemble. Now the solinoid assembley is easy to get to. Use a phillips screw driver and remove the two screws that retain the bracket that holds the solinoids in place.. Lift the bracket and remove one solinoid at a time. Pull the wire from it and plug the new, like solinoid to the wire and put it back in place. then do the other one. set the bracket back over the new kit and replace the screws to the bracket. Set the tub back in, rethread the belt to the drive wheel. Next put the front back on making sure the bottom part slips into the two sides of the dryer.Replace the hexhead screws on each side; plug the wire connector together. Now , pull the lid down into position and press into place. Replace the lint trap screws and replace the lint trap. Plug dryer up and we are done. Repossition the dryer to its original place. It really was not a hard job at all. Thank-you Susan for your help and expertise.

I ordered the part(and a backup) and had it in two days. 5 days less than ordering from sears.