11065102310 Kenmore Dryer - Instructions

The dryer was igniting when initially starting load, but didn't light again the rest of the cycle. On my model the access was through the front panel, didn't even have to pull dryer out. Open the door and there are two screws on each side.of the inside of frame. Remove screws and lift door off the the whole front of the pulls out and down and removes, and everything is right there to work on. Replaced thermostat, that took 5 min. But didn't fix the problem. So I purchased and replaced the "M" Series New Style Coil Kit, took about 10 min. I took olm/continuity readings b/t all terminals of the old and new coils and they were only about 5% difference, the old being a little lower. But that fixed the problem, works like new again.

I bought a new thermo cut off and replaced the old one.

I unplugged the machine and removed the back panel with a 1/4" socket. I unplugged each thermostat in turn and pulled them out. The internal bias was a bit tricky to remove without breaking the tabs or wires. I then placed each thermostat back in and replaced all the wires. Not bad at all. Weird thing is the dryer heats just fine now, until I put the back panel on; once I replace the back panel, it will not heat.

I ordered the part(and a backup) and had it in two days. 5 days less than ordering from sears.

Followed the video and stopped at each part not one issue very easy repair most difficult was separating the electric from from panel a little tricky to get apart.

Unplugged the unit, removed the back panel of the dryer and then removed the thermostat panel. Disconnected the wires on the thermostat and changed out the thermostat.

still no heat.

Replaced thermal sensors.

The repair video provided for this model 110.97584810 gave erroneous info. It says to remove the back vent cover. The back on this model is not removable. I wasted an hour trying to remove back and top of dryer before discovering that the bottom front panel below the door pops off. Then the cover of the blower must be removed by removing two screws. The thermostat part can then be accessed and replaced as shown in the video. You'll need a 1/4" rachet to remove the screws as there isn't space to use a nut driver. Note that the statement in the video "This repair is done all from the back" is completely wrong. It is done entirely from the front. It can be done without even moving the dryer.

Followed the video - easy!

First I watched the repair video on-line at this site After pulling the dryer away from the wall and unplugging the 220 volt power cord I removed the back panel with the 9 screws. I then unplugged the wires to the thermostat/heating element. With an ohm meter I discovered that the heating element was good and the high limit thermostat was bad. I ordered the high limit thermostat from this site on a 2 day shipment. When the part arrived I installed the part and the wires. Plugged in the dryer for a quick check for heating. Replaced the back panel and moved the dryer back into position. Dryer works fine now.

Read this site and saw many fixed the problem with a new thermostat. Ordered one and it was simple to replace. Just removed the back panel of the dryer and the thermostat is right there. Two screws to remove it, swap the four wiring plugs onto the new one, reinstall it. Unfortunately that didn't fix it so went back online and ordered the coil kit, another common solution. Removed front of dryer by removing the two screws the hold the lint trap onto the top and the two hinge plate screws on back of dryer to tilt the top up ward and backward. Removed two mounting screws on inside of dryer front and slip front panel upward to remove. The coils are right in the front down at the bottom left of dryer.Used an offset screwdriver to remove the two screws holding them in place. They slide right out, one has two prongs, one has three. Replace them with the new coils and put them back in place. Reassembled and everything works now. Grand total of eight screws removed and replaced, pretty simple. I'd recommend buying two or three parts if you see several parts as possibilities for a repair. Easier than doing it the dummy way like I did!

Thank goodness the part was still available for a 25 year old dryer. Website was great to help solve the problem and the video was wonderful to show me how to identify the part and how to get to it. You take off the back of the dryer and then unscrew the thermostat from it's mooring. Undo the 4 wire connections. Stick in the new thermostat and re-install. Thank you!

I fixed it with my soccer set I took the lent thing off and clean it out was stopped up with lent didint need the parts I order but I will keep them for the future.

See video.
Two additional tips:
When disconnecting the door sensor slide the putty knife under the plastic latch from your right.
Use clothespins to hold the felt seal in place during glueing process.