11066132410 Kenmore Dryer - Instructions

followed the repair video .. unplug dryer ... removed screws on lint trap .. popped the top off the dryer .. removed the two screws on the switch ..unplugged the switch using a small screw driver .. replaced switch .. put it all back together .. it took about 20 minutes

An online video provided perfect instructions. Unplug the dryer. Remove the Lint filter and see two Phillips screws located on the top of the machine, then remove the screws. Then slide a stiff, thin putty knife under the right front corner between the top and the front panel. The clip inside has small feet holding it in place, so you need to angle the putty knife up slightly, then push in towards the back of the dryer while lifting up on the top. The corner will lift away from the front. Repeat the process on the other front corner. Now lift up the top that is hinged at the rear. I used a 24" 1 x 2 board to keep the top up. Open the front door and remove the two screws that hold the switch in place then unplug the switch on the inside of the dryer and remove. Plug in the new switch (2 or 3 wires may be present, but it doesn't matter). Attach the new switch using the two screws you removed. Lower the lid and tap each front corner to reengage the clips, then put the two screws back in at the lint filter. Replace the filter, plug the dryer back in, and you're done. I honestly think that it took longer to type these instructions than it took to do the actual repair.

I love this site! They make it so easy even a woman can do it. Love the diagrams, the trouble shooting helps and reviews/instructions! I followed the printed instructions. Unplugged the cord, removed the lint trap and removed the two screws. Put the lint trap back in and pried the top off. One corner was a little harder than the other but got it! Just lifted the lid just enough to reach the switch right inside. Tried unplugging the old switch, but it didn't come right out. Hubby had to help by using a screwdriver to "unlock" the plug. Then unscrewed the screws on the front of the dryer, inside the door holding the switch. But hold on to it because we dropped the old switch right down into the bottom of the dryer...where it will forever reside since we couldn't find it or get it!! Plugged the new switch in, screwed the screws in to hold the switch in place. Took a little effort to get the screws lined up with the holes on the switch but we got it! Replaced the top, removed the lint trap, screwed the two screws back in, plugged it in and wa-lah! The light came on and the drum stopped when I opened the door! So simple!

I followed the you tube instructions. Unplugged the dryer. Removed the lint screen. Unscrewed 2 screws. Used puttty knife to open the top of dryer. Located the door switch and unplugged it and replaced with new part. Closed top. Replaced two screws and put lint filter back in. Plugged dryer in and turned it on. It worked like new. I'm a woman and this is second part I've had to replace on this dryer. Watch you tube video.

The videos on replacing the switch mentioned using a putty knife to pop the top of the dryer open. My dryer is around 10 years old, so a putty knife wasn't strong enough to pop the dryer top off of the clips. Instead, I had to gently stick a flat head screwdriver and twist just to the side of each clip. Other than that, the video instructions were spot-on on for replacing the switch: UNPLUG THE DRYER FIRST > remove the lint collector > remove the two screws from the top of the lint collector's slot with a Phillips screwdriver > pop the top of the dryer up gently with a flat head screwdriver (or a putty knife, if that works for you) > remove the two screws holding the switch onto the front of the dryer (it would be good to notate which direction the switch is pointing) > use a flat head screwdriver to pry the faulty switch's clip off of the dryer's wiring harness clip. Then reverse the procedure with the new switch: plug the new switch into the dryer's wiring harness > screw the new switch into the slot on the front of the dryer, making sure that it's oriented in the correct direction with the switch's arm pointing away from the dryer > lower the top of the dryer back down and press it onto the clips > screw the screws back into the lint collection slot > replace the lint collector > plug the dryer back in > test the dryer.

followed the enclosed instructions, used a balled up towel to support the drum while attaching the belt and tension pulley, took about 20 minutes

I thought I had checked the arm piece of the rack real good for a product number on my original part but I missed the number till the 2nd box came in, and a looked real careful and realized it was the same as the order I thought was bad.
Put the spring arm in first and the rack will fit in the front groove.
It would have been good if there had been a picture of the dryer arm attached to the dryer.
So I have 2 good racks and will return one if you tell me where to send it.
Keith Walden..

Turned off breaker to dryer. Removed 2 lint trap screws, raised top of dryer & unscrewed switch. Replaced door switch, closed top, replaced the 2 screws that hold lint trap, lowered top, then turned breaker back on.

I followed your online video of how to install the new part . I did have an issue getting the top cover off the machine - the video said to pop off at tabs but no such existed- I had to remove 4 screws on the back of the dryer & lift top off - no big deal Then I had some trouble getting the old part unplugged - required two pliers either side to pull apart- VERY securely fastened. Otherwise just so so simple. FIXIT housewife!

Did as your video instruction. To me the order of work needs attention: Remove the switch, unscrew 1st, then remove the hook and wire connection. Installation: connect the wire first, then hook to the frame, the last step is screw in the switch. That should prevent accident dropping the switch inside the dryer.

Plugged in the switch, put in (2) screws and finished.

I removed the part located on the dryer at the top of the door area. I installed the new part with the two screws I removed and BAZINGA...it all worked again. Very pleased!

Installed new door switch, so, so simple. Unplug dryer, remove lint screen, undo 2 scews located at base of lint screen opening. Use flat head screw driver to pry up dryer top, once open, rest the top against the wall. Now you will see the door switch in the right hand corner at front of the dryer.Open the dryer door , remove 2 screws holding the broken switch, disconnect wire from dryer, click in the new switch, put everything back together, plug in the dryer and go! Super quick and easy, wish I had just done this months ago!!!!

Unscrewed the inside part of the door from the outside door shell. Removed the broken pieces of the catch and replaced it with the new one. Screw the door back together. Did not need to remove the door from the dryer cabinet.

This problem occurred Thursday afternoon; after I took out a load of dry clothes, it wouldn't restart. I realized that the switch was busted, it used to click but it was just hanging. Watched the video and ordered it right away. It arrived Saturday morning via Fedex and I installed it in about 5 minutes. It probably took longer to watch the video. 23 bucks and the dryer's running perfectly. I've replaced several parts this way on my appliances, always feels good to do it yourself. Good as new.