110C60242510 Kenmore Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Henry from CHEYENNE, WY
- Parts Used:
- 4392065
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Noisy, screeching, sounded like roller bearings were shot
Watched the video, followed the printed instructions for reminder when necessary. Needed a second person briefly to hold the dryer tub when installing the new belt, and also when removing/replacing the front panel. Beyond that, it was straight forward and relataively easy to do. Solved the noise problems and it dries more evenly now as well. The one thing the instructions don't say is to check the rear canvas seal when the tub is re-inserted into place to assure it doesn't fold back on itself.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from EVEREST, KS
- Parts Used:
- 349241T
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
rollers had been new too long!
Took of the btm pan and the top to be able to remove the front. Raised the drum enough to replace the right hand wheel. ( the old ones had already been removed) Replace the left hand wheel and bracket. Re assemble the machine. Worst part was trying to do all this with the can of beer in one hand!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from HUDSON, MI
- Parts Used:
- 4392065
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Socket set
Drum wouldn't move. Belt Broken.
Opened the cabinet and removed the drum. Cleaned out the dryer fuzz. found that the roller stabilizer wasn't in place; apparently due to a previous repair. Replace both rollers and the roller stabilizer and prepared to replace the drum. But because I live alone, I didn't have anyone to hold the drum while I connected the belt to the motor. But, I did have three unused balloons which I partially inflated and set the drum on them in the bottom of the cabinet while I hooked up the belt to the motor. Put everything back together and it is now drying my clothes again. :)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Margo from FOX ISLAND, WA
- Parts Used:
- 4392065
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Dryer was making bad noises like a bearing was going out, then it got worse and sounded really loud, so I couldn't even run it.
Followed the instructions found online. Only thing I would add is that the clips are easier to work with if you warm them up a little before you try to install them.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- STEVE from FULDA, MN
- Parts Used:
- 4392065
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
drum roller were worn out
flipped up the top pulled the front off easy access to drum removed the drum replaced rollers per instructions that came with package. very eas job. works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- charles from waukesha, WI
- Parts Used:
- WP3387134
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Wrench (Adjustable)
dryer would heat up once on a full hour cycle
i took a stab that it was the thermostat,but it wasn't.after finding out it was the coils i purchased them and lifted the top of the dryer and undid two screws in the upper front of the dryer and lifted the front off all while holding the tub in place.The coils are located in the very front left of the dryer,i took the holder bracket off,disconnected the wires and replaced the coils(they just sit on a rod)dryer works like new and thanks to the new thermostat also gets hotter,i'm guessing that was next.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Keith from Shawnee, KS
- Parts Used:
- 3406839
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
I had only seen a one piece rack .The 2 piece threw me for a loop.
I thought I had checked the arm piece of the rack real good for a product number on my original part but I missed the number till the 2nd box came in, and a looked real careful and realized it was the same as the order I thought was bad.
Put the spring arm in first and the rack will fit in the front groove.
It would have been good if there had been a picture of the dryer arm attached to the dryer.
So I have 2 good racks and will return one if you tell me where to send it.
Keith Walden..
Put the spring arm in first and the rack will fit in the front groove.
It would have been good if there had been a picture of the dryer arm attached to the dryer.
So I have 2 good racks and will return one if you tell me where to send it.
Keith Walden..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Katharine from PERRYSBURG, OH
- Parts Used:
- W10612022
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
The issue was I saw pieces of the felt in a load and all fell out a few days later Dryer started to make noce rotating once it got metal to metal stopped immedietly
Followed the video and stopped at each part not one issue very easy repair most difficult was separating the electric from from panel a little tricky to get apart.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Allan from JOHNSTON, RI
- Parts Used:
- 4392065
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
belt worn
replaced rollers, belt and pulley. Video was very helpful
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harry from BEVERLY HILLS, FL
- Parts Used:
- WP3387134
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
dryer overheat
Replaced thermostat on back of dryer, very easy to do, took about 15 minutes after watching video . doe's not require rocket scientist to do.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from COLLIERVILLE, TN
- Parts Used:
- WP3387134
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Gas dryer would heat but shut off as it warmed up.
Removed the back panel of the dryer. Thermostat is located in the out going air flow near the exhaust. Removed one screw that held thermostat. Exchanged wires and put everything back together
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dougls from Coconut Creek, FL
- Parts Used:
- 279816
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Socket set
Dryer not heating, but motor running
I first unplugged the dryer and pulled it away from the wall. I had to remove the vent tubing to gain access to the rear of the unit, then removed the screws on the back panel of the dryer. I took off the panel and noticed that lint that had gathered over the years around the back of the dryer. I vacuumed it clean then proceeded to problem solve. I noticed four easily identifiable areas, the thermal cut-off switch and thermostat located by the heating coil and the thermostat and fuse near the venting area. I first checked the fuse with a ohm meter, it was okay. I removed each component one at a time and created a bypass with a alligator clip wire. Plugged the dryer back in to determine if heat was produced while testing each area one at a time. I determined that heat was produced after bypassing the thermal cut-off switch. I then ordered the thermal cut-off switch kit (arrived within 3 days) and installed it within 20 minutes. The longest time spent was trouble shooting, the removal and installation was very easy. By the way, I did use the ohm meter to check the resistance across the thermostats as indicated in previous postings, but I found the results and technique to be more confusing. A bypass worked the best for me and much more reliable. The heat started immediately. I highly recommend downloading the schematics of your unit for part number and location identification.
Was this instruction helpful to you?
Thank you for voting!
The Dryer would not heat up
I unplugged the machine and removed the back panel with a 1/4" socket. I unplugged each thermostat in turn and pulled them out. The internal bias was a bit tricky to remove without breaking the tabs or wires. I then placed each thermostat back in and replaced all the wires. Not bad at all. Weird thing is the dryer heats just fine now, until I put the back panel on; once I replace the back panel, it will not heat.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jose from SANDY SPRINGS, GA
- Parts Used:
- W10612022
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
remove, take off , install
just remove 4 screws removed the drum and put the affected part and that's it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Marion, KY
- Parts Used:
- WPW10512946, 349241T
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set, Wrench (Adjustable)
Noise in dryer when dryer was turned on
Removed the drum then removed the old parts and installed the new ones. Dryer now runs very quite and heats good. You have very fast service my mother ordered the parts on the net one day and I received the parts next day and did the repair that night and dried clothes. Thanks,
Your great service is very hard to find.
Your great service is very hard to find.
Was this instruction helpful to you?
Thank you for voting!