11068132410 Kenmore Dryer - Instructions

Used the maintenance kit....followed the movie tutorial. I also used an empty gallon plastic container to support the front of the drum while stretching the belt over the motor pulley. For the rear drum rollers, before sliding them on the shaft, I put a light grease film on the shaft. After the repair, the dryer runs quieter.

Replaced power cord, terminal block, and all melted wiring. Checked the thermal fuse for zero resistance.

I removed the bottom access panel, with 2 hands i reached in behind the blower, i released the belt, i used a screwdriver to pop the retainer from the pully spindle, i removed and replaced the pully, i snapped the retainer back on and replaced the belt. I made sure the belt was on track and all was good. I put the bottom panel back on, it took all of 5 minutes. The hardest part was the retainer clip faces the rear of the dryer so you have to feel it. Also , the space is tight, use a smaller flathead screwdriver to get behind the clip, it will pop right off.

Take pictures along the way.
1. Remove lower front panel using screwdriver to lift up on tabs on top of panel.
2. remove door
3. unplug moisture sensor plugs
4. remove lint trap
5. on back of dryer, remove screws holding upper lid
6. slid up lid forward just a small amount, its hooked in towards the front of the upper lid. you will need to do this so you can can remove two screws under the lid holding the front panel of the dryer on
7. remove the front panel screws mentioned in step 6.
8. Remove lower front panel screws
9. remove front panel
10. reach into dryer at the bottom and release tension from belt pulley, sliding the belt off. (make a note of how the belt is routed around the drive and idler pulleys)
11. slide out tumbling drum
12. with drum removed, use socket wrench and socket to remove old idler pulley.
13. install new idler pulley
14. reinstall tumbling drum
15. slide belt back around tumbling drum, looping belt around drive pulley and around idler pulley.
16. When belt is installed, rotate drum a few revolutions to ensure belt rides correctly.
17. Reinstall front panel
18 slide top panel back into place and secure with screws from back
19. reinstall door
20. reattach moisture sensor plugs
21. reinstall lower panel

Perfect!

As seen in video, All Good !

Unplug dryer from 220VAC outlet

Remove bottom cover panel, slip a flat blade screwdriver into each clamp, and bottom piece becomes removable. Pull forward and lift bottom cover piece.

Pull up top section from dryer frame. Disconnect dryer door off/on contact three wire switch by pressing plastic connector together. You may need a small flat blade screwdriver to seperate connector.

Remove two Torx (T15 head) screws in the far left and right corners of the front door panel.

Remove two screws underneath dryer lint screen, be careful to not let front door and front cover fall forward. The rotating dryer drum will now be loose.

Underneath drum, there is a cover panel over the dryer motor. Likely you will find a bunch of lint all about. This dryer had likely not been cleaned in many years.

Remove screws on dryer motor cover.
Remove panel. Likely, you’ll more lint about.
After vacuuming, use a flashlight and hand mirror to locate belt tensioner, back side of motor. If your belt is not broken, press down on the tensioner spring and remove belt from tensioner and motor. Inspect belt, replace if worn. In this instance the belt was well worn.

Slowly pull dryer drum forward, walking belt along as you bring drum forward out of the dryer casing.

At this point you have plenty of room to access the one bolt holding the tensioner, in this instance it was a 13mm socket. Be careful to remove the tensioner springs before removing the bracket. Your PartsSelect is an identical match to the original one.

Install new tensioner, tighten slightly, then put springs back on.

Reverse this entire process to get your dryer back together and back running smooth and quiet as it was when new.

This dryer was quieter than its owners remembered it being back when new 15 years ago.

Well worth saving the $ doing your own work.

Good luck on your repair endeavor!

You tube and supplied video directions for the make and model. Follow step by step and the repair went easy. Worried when removing the dryer drum but it went smooth.

Took the back and top off of my front loader. I had checked on you tube for the problem and how to fix it and ordered the part. Just followed the directions on how to remove the old idle pulley and installing the new one. Dryer runs like new!

Ezee pezee lemon squeezee.

Simply followed the video that accompanied the part confirmation. Removed the top and front of the dryer. Removed the drum and belt. Unbolted (1 bolt) the Idler pulley and bracket and bolted on the new one. Reversed the sequence of disassembly and tried it out. The only minor difficulty was slipping the belt over the idler pulley after the drum was in place. This is where a second set of hands might be helpful to hold up the drum, while the other person puts the belt in place. Other than that, this was a simple repair and probably saved a couple hundred dollars for about 1.5 hours of my time. Thanks for the video...it was right on point, and made the job much easier.

Removed top cover. Removed front cover. Removed Drum. Located the broken belt. Found that there was no tensioner in the unit. Replaced drum rollers. Put in new tensioner. Repaced Drum with belt around it. Installed belt through tensioner and onto drive pully of motor. Supported Drum with wood block. Turned on dryer to insure drum turned without any problems. Removed wood block. Replaced front cover and top cover. Repair compete.

The pulley is accessible from the back of the dryer. Disconnect the gas line. Remove all the screws. Also remove the small plate that secures the line cord. Lift the back up and out. I was able to avoid disconnecting the water line. Take a picture of the pulley so that you will have a record of the belt routing. Release the spring and remove and replace the pulley and bracket. Vacuum out the lint. Plug in the dryer to make sure that it works properly before reassembly.

Couple screws behind the electrical panel at the top and the top pushed back and was able to remove front panel, and then it was pretty easy. Take the two screws on top front, lint trap screws . The lint trap vent needs to come off. Then the belt, drum comes out to access the idler pulley. I did replace two drum wheels, I saw there was 5. I would recommend replacing all of them, they didn’t move well…..

I changed the belt, tension pully and rollers. Runs like new now. I also took the opportunity to clean it out real good while I had it apart.