11072332512 Kenmore Dryer - Instructions

this was very was very easy. But I deviated from the You Tube instructions. One to release the motor pulley. I needed to use 2 adjustable wrenches for a longer lever. I needed to use a hammer to help release pulley. Second to remove the dryer cable I needed to use a small screw driver to aid in the release. ---- the part from the company was a perfect fit.

Removed 2 screws in the lint filter and popped off the top. Removed the 2 screws holding the front panel on. Slid the drum off and set aside. Replaced support rollers. Placed the belt over the drum and placed the drum back in the dryer. Wound the belt over the tensioner and motor pulley. Turned the drum to keep seal from folding up. Replaced front and top.

Tip: Use bungee cord or rope to hold top up and out of the way while doing this job.

Went to the site for instructions. Received a nice set of three photos with detailed instruction. Very easy to follow and item just snapped in. If I hadn't looked up the instructions I would have probably risked breaking the new part.

1 screw to replace.

Sensor is in the front lower left. Gas off, electicity off. Removed two screws for the filter, pry/lifted the top up and taped it too the overhead cabinet, removed two screws inside top of front panel, lifted pandel with door closed staight off. Two screws to remove the flame sensor braket. unplug the old sensor install the new one and reverse everything. With others suggestions I purchased temperature switches etc. but the radiant flame sensor was the problem. I now have some spare switches for future. Excellent company and very quick service. Oh, Sears wanted 200.00 just for the service call, I live rural.

The repair was fairly straight-forward. I removed the front of the dryer, lifted the top off, and then released the tension off the belt dy depressing the pulley arm. Once the belt was off, the drum came right out and then it was on to unhooking the wiring from the old motor. Very simple up till this point. The snag came when I went to unthread the impeller fan off of the old motor shaft. It was permanently sealed onto the shaft so I had to cut the old shaft into using a reciprocating saw was a metal-cutting blade. Once this was done the new motor installed easily exactly like the old one was mounted. I had to also purchase a new fan due to the fact that I was unable to remove the cut shaft from the old fan. All parts worked great and the dryer assembled back together easily. Works like a new dryer now.

removed frt & rear panels & drum and lint chute for seal replacement replaced these components, problem didn't go away, ordered & replaced both gas valve coils (m series coil kit) problem solved

lined up the holes and pushed. 2 second repair.

First i removed the rear panel on the dryer.the removed bothe thermostats that were on the blower housings.unpluged all wiers and installed new thermostats.reinstalled the wiers in there proper locations...note to log the location of the wires when removing from old switch.reinstalled the rear panel and hooked dryer back up and test.

I have not received the parts yet waiting on the motor, can’t put the blower fan in without the motor, ordered it , Jan 23rd, still no motor, have to go to laundry mat, have you ever had to do that with 7kids, and you and your wife’s laundry, probably not, because you would have had your motor by now. Maybe you can help me with the part so I can redo a testimonial here for you. 19 days and still waiting

Took back cover off. Cleaned out the lint that had built up inside the dryer. Replaced the lint trap housing and lint chute seals. Also replaced the drying vent hose. Works great now.

Be very careful of burrs on the edges of the steel inside the dryer. I cut myself badly when reaching into unplug the switch.
Procedure: Lifted the dryer top by pulling forward and rotating front up. Removed 2 philips screws holding the switch at the door. Reached into dryer and unplugged bad switch. Inserting small blade screw driver at the edge helped release the plugs detent. Installed new switch using reverse of above.

Easy, just snapped it

Actually, I was the handy man. First I removed the front panel. Then I used 3 - 2x4s to hold up the drum. Then I slipped the belt around the center of the drum ,motor,and around the pulley at the bottom of the dryer. That was it, and then I put it back together. My wife was amazed and proud that I did it without calling for help! No Problem!

Take out 2 philips screws in lint trap holder on top. Use flat screwdriver to pry up front left and right of dryer top near outside edges and tilt up out of the way. Remove 2 push-on AC connectors on door switch and remove plastic clip holding wires to dryer's front top metal edge. Remove (2) 5/16" sheet metal screw on inside top left and right edges to free up front panel. Lift front panel about an inch and it'll then pull off. It helps to have a second person to help hold or remove the drum at this point. It took 3 times for me to guess right on the squeak. First time I replaced the belt, second time I replaced these rollers, third and final time I replaced the idler pulley, the shaft of which had worn completely off so clearly i can't figure out how we didn't see (or hear) it the first two times! Dri-Slide lube helped stop the squeaking the first two times, but it always returned until this time, now I have a thoroughly rebuilt dryer for the next generation! (PS vacuum out the bottom of the dryer while it's open to remove both lint and greasy roller shavings - do this FIRST and you'll have cleaner hands & clothes!)