41791122311 Kenmore Dryer - Instructions

Dryer was working, only burner was working occasionally only. So, in result the drying time was very long, and clothes were cold and still not satisfactionally dry; occasionally only it was hot. It became obvious to me that gas burner only occasionally is working. On the Internet I found some instructables, mostly on YouTube, but also on this site (the Burner diagram): thus I have learned that the culprit must be the two tiny ignition coils: they worked only sometimes, so it was only a jeopardy when checking them using a continuation meter (voltmeter with continuation feature). For the access to the burner combo I used a small checking door right below the large door, in front wall of the dryer. There are only two small screws which hold a small piece of metal which cover these tiny coils. However, I had to disconnect the burner from gas pipe to get better access to those screws. (Of course, I also disconnected the dryer from power and I had to disconnect those wire connections on the burner combo to get access to the burner). It works perfectly after this repair.

I lifted the top at the front edge, slid the top back, disconnected the ground wire connected to the top at the rear edge, just slides off.
Then removed the phillips screws on the inside front edge, only one on each side,near top of dryer disconnect the wiring harness at the right side, cut the nylon tie strap holding harness also.
Tip front panel out a little and lift up, comes right off.
The coils are in plain site on the gas valve, remove the wires, and the two screws holding the bracket that holdes them in place, slide the old ones off and start putting back together.
I also used a vacume and cleaned all the lint and dust off everything I could, including the air intake at the rear of machine, "Peice of Cake"

Very slowly and carefully, you tube videos and schematic very helpful.

I seen a post on your website referring to the exact problem I was having. One of your staff recommended changing the control thermistor, which I did following the U-Tube video link you supplied. The repair went well and the dryer now operates perfectly ! Thanks for the accurate and helpful info.

Cover of the dryer pops off and hinges back. Use a flat screw driver to pop the clips on the front sides. Two phillips head screws hold the front panel on. Remove them then lift the panel off the clips at the bottom. Two phillips head hold the Ignition Coil bracket in place. Take note of the direction of the cable connection, it's not marked. Dryer would ignite intermittently. Clothes were not dry after 1 hour.

Unplug dryer.
Put up the top of the dryer at the front, remove 2 screws holding the front of the dryer to the sides and remove front of dryer. Locate ignition coil on lower left. Remove 2 screws and bracket over the two ignition coils. Replace coils and reassemble in reverse.
Everybody's happy.

my experience was just like the other responses. top comes off, 2 screws and the front comes off and the screws to the solenoids come off. Replaced the solenoids and put everything back together.

All I had to do was pop in the new door catch. Works perfectly.

Removed burner, unpluged 2 plugs on coils. Removed 2 screws, replaced coils, pluged 2 plugs to coils replaced 2 screws. Reinstaled burner. Dryer works great.

Unplugged the electricity, turned off the gas, then pop open the top of the dryer. Removed the two screws and pulled the front of the dryer off. Removed the two screws that locked down the two m series ignition coils. Put it back together and all things worked great.

Very easy fix on this system as described in other reviews. Simply unplug, lift top, remove two retaining screws on the dryer face, remove face from front of drum. Locate both coils at the lower left corner of the gas valve assembly.

parts arrive just like they said they would .had parts installed with in 15 minutes was drying clothes thank you your advice was perfect.

Popped the top... disconnected wiring... dropped the front... replaced coils... reversed sequence... done deal. No hassle, no worries, easy as 1-2-3!

There was a small plate and 2 screws holding the 2 coils. I just removed the screws, unplugged the 2 coils, plugged the new ones in and put the dryer back together.

Followed instructions and the repair went very smooth from start to finish. From getting tools out of tool tray to putting them back it took 15 minutes.