11061202013 Kenmore Dryer - Instructions

Broken belt, but went with the mainentance kit since it was going to be all apart anyway. Found the job easy to do and the new belt idler was a big improvement over the old style. /also came with instructions. Good for another 5-10 years.

Using a stiff putty knife I depressed the clips that hold the top down. I loosened the screws at the lower edge of the front panel and removed the two 5/16 head screws that hold the front on. I unplugged the door switch and lifted the front off the lower screws. I removed the drum and the broken belt. I replaced the rear rollers after applying some dry lube to the shafts and replaced the tension spring and rolled. I replaced the drum and belt and attached the belt to the small pulley on the motor. Then checked the rear gasket felt and reinstalled the front cover and the top.

Watching the video from Parts Select for replacing the rollers showed us all we needed to easily replace the wheels as well as the Pulley and belt. It made a gigantic different in the noise and efficiency of the dryer. One of the Wheels was actually 3/4 gone, worn away. Hopefully, this repair will extend the life of an already old dryer. Thanks for the videos that made the repair a 'piece of cake'.

it was easy all the parts were the exact replacement

Followed instructions supplied ( very easy)

Had to order idler lever and wheel as the one in the kit would not work. Best to buy part specific for your dryer. Repair was easy, just watch repair video. Sounds like new dryer again

Diagnose the problem. Is it the motor ? Is it the belt ? Order the correct repair kit, use name brand parts to ensure reliability. READ THE SUPPLIED DIRECTIONS. You can use a small wood shim or wedge at the top front corners to open the top . Use a 5/16" socket to remove the 2 screws at the top outside corners. Lift the front panel straight up, supporting the drum as you lift it off. Remove the drum, taking it straight out the front. Install the new drum rollers, install the idler, and then the belt around the drum. Install the drum on the rear rollers, make sure the seal is not folded under. Push the drum back against the seal flange, support the front of the drum with your right (or left ) hand, and sit the front panel on the lower pins, and gently push the front panel to the sidewalls. Feed the belt through the idler and around the motor pulley. This job is easily performed in about 20 minutes. Clean the interior while replacing the belt/idler and drum rollers. With the top lifted, after assembly, test run the dryer to make sure there are no "funny noises" after the repair. Watch especially for the white rub strips on the front edge of the drum. They tend to fold over when attaching the front panel. Job done !

Ordered entire Maintenance kit - good call because it was the tensioner pulley that failed and cut the belt. To replace, had to raise the top (2 screws in lint screen slot)and pull the entire front off (2 screws - 1/ea on top inner edge of front door panel then lift it up and out) Replaced both rollers, then used the parts kit shipping box to prop up the front of the drum while installing the belt and tensioner pully. Re-assembled in reverse order, works fine.

Everyone said changing a dryer belt was a piece of cake.They did not tell the truth it is a difficult job. I am a 52 year old female and I had a problem. You have to take the whole drum out. I finally completed the job but i had to prop the drum up with blocks so I could screw in the front panel. I think for those who want to change the belt I would go smoother with two people so the can hold things in place while the other one screws the panels back. I also think taking the dryer door off make the front panel a lot more easier to put in palce.

I purchased the maintenance kit and followed the video on part select.com. Replacing the drum wheels, pully and belt was not difficult. I probably found enough coins in the dryer to pay for the maintenance kit. The only tricky part was getting the cap on the end of the axle. It requires a bit of force applied evenly.

I simply followed the instructions, replaced the belt, tub support wheels and tension pullie. Could not have been easier. I figured it was worth $47.00 to buy the kit and if it was another issue, at least I saved money vs. a service call. There are only so many things that can go wrong and the belt was the fix. 20 yr old dryer works just like new.

Very detailed instructions.

I reviewed the instruction video. Excellant video. exactly like my dryer. Just followed the instructions. I did put a shoe under the drum for easier installation of belt onto idler pulley. I vacuumed and cleaned inside. Really not that dirty.Excellant web site and video instructions. Wish I had done the repair sooner. Also God Bless the residents of OK city, Moore, and ElReno.

Basically, I just did everything in the Parts Select video - it's what gave me the courage to attempt the repair myself and I am a 61 yr. old woman, who's not in great physical shape! The belt had broken. The two things that gave me the most trouble were disconnecting the tab on the door switch assembly and getting the screws to line up when replacing the front panel - one side lined up fine - the other needed a good push and an "alley-oop" to the side with my hip to fall into place. I did a few things that were not in the video which I think really helped me out. (1) I put an empty quart sized paint can under the dryer drum to hold it up - that really helped - I only had to support it slightly myself when threading the new belt. (2) I put a piece of duct tape across the bottom of the idler pulley to keep that from falling out of the holes when I was threading the new belt - that worked like a charm. Just be sure to remove the piece of duct tape and the paint can before you close up the dryer, if you decide to follow those two tips. (3) I also eventually put something under the front door panel to help raise it up and get it more in line with the two holes that it connects into, which made it easier for me to get it back into place. (4) Have some bandaids on hand - I sliced two fingers on different parts while installing the whole kit. (5) After you are done, either clean out the dryer vent hose or put a new one in - I was surprised by how much lint was clogged up in there. I never repaired any appliance before and if a 61 yr. old weakling like myself can do it, anyone can. Parts Select Rocks - the kit arrived a day and a half after it was shipped out and the video tells you everything you need to know to do this repair yourself and save big money. $49 versus probably $150 for a repairman and $500+ for a new dryer. Dryer is running like new! Would definitely do this again, if this or another dryer broke in the future. Thanks!

After watching your video, and reviewing the directions, I was able to change the rollers, the belt and tension bar with ease. The parts cost me slightly under 50.00 and now the noise is gone and my dryer works great. I am very pleased with PARTSELECT and would use them again. The parts were at my house within three days of placing the order !!!