1106118231 Kenmore Dryer - Instructions

After removing front door panel (2 screws) I removed the old latch catch and replace with the new part. 4 minutes later, the door was back together, the dryer was running and the door was staying closed.

took the cstch reciever out, with my fingers, pushed the new one in, snap lock fit.......couldn't be better, like repairing a model T ford.......

the part fit perfectly, it just snaped right into place.

The only thing I had to do was hammer the catch inside the square fitting and presto it was done. It took me less than 3 mins. I thought I might of needed instructions, but it was really simple. Even a guy can do it. (smile)

I replaced the male end first hoping that a change in the female part would not be needed. Unfortunately no. I used needle nosed pliers to pry the male part out and pushed the new part in. The female part of the door catch was more difficult. I didn't do it in "textbook" form, but got the job done with pliers and a screwdriver. Worth every penny to fix correctly instead of rigging it. Do it!

Followed Youtube video - quick & easy

Followed the video instructions which were comprehensive, easily understood, and prefaced with a listing of necessary tools. Completely satisfied with parts and supplementary information.

Popped out the old door catch kit and replaced it with the new one! Easy!!

Simply installed the piece and I was done. Took 10 seconds.

The door catch kit is soo easy. They give you instructions on which one to use depending on your dryer and it fit perfectly into the door. This was great especially since it was so inexpensive! My husband thought we would have to replace the door.

I ordered the door catch kit on a Wednesday at it arrived Saturday AM. It took less than 1 minute to pry out the old catch with a flat screwdriver and pop in the new one!

Popped the latch out and popped a new one in.

The real story here is that there was an ANSWER and a SOLUTION, to what was a GREAT
annoyance. If I wouldn't have found a part, I may have run off and bought a new dryer, when I really didn't need to, or paid A LOT of money for a repair man to come out. THANK YOU for your service. You made my life easier.

All I had to do was get the model number off of the dryer and plug that information in online and within a couple of days the part arrived. It was great! There were directions that came with the part that explained how to replace the old latch with the new one.

I remember in the "olden days" when I would of had to call a repair guy out and paid a lot more than the $12.00 I did to replace the part myself. And, the only reason it was $12.00 dollars instead of $5-6 was because I had it shipped overnight.

Awesome!

Your web site is amazing Ive enjoyed watching your videos,this is a really great way to see what it takes to repair your washer very informative. Steve was a good teacher for me I just followed along as he explained each step and my washer came apart just like he said. I removed the two front console screws and pulled slightly forward and lifted console up and tilted it back where it was out of the way. next I was able to lift cabinet up from the back and remove it from the frame and lay cabinet on the floor on top of a rug I had to protect the finish on cabinet . Now I had access to the lid switch and simply removed the two screws in the cabinet and the old switch. I connected the two wire connections to the new switch (no)normally open connection, used same actuator the instructions say to do this because the one that comes with the new switch won't fit so use the old one. on my washer there's a cover that fits under this switch and It took me a little longer to get the screws to line up so they fit through the switch and into the cover but It worked fine. Now all I had to do was reinstall the cabinet just like Steve did on the video my only problem with this was seeing where the tabs in the frame were located so that the slots in the cabinet would fit over top of frame tabs I used a flash light in one hand and lowered the cabinet down I held the light on the frame tabs and the slots in cabinet fit right in then lowered cabinet to the rear frame tabs where i just had to push slightly on the sides of cabinet and it fit right in.Next i pushed the back panel in place and on the top of washer just like in video reinstalled both spring clip clamps and the console and reinstalled the two screws. I plugged in the washer put drain hose back in drain pushed washer back in place turned it on working great now ! Thank You so much for your help Dan.

Removed old catch and strike with screwdriver and needle nose pliers. Installed new parts. My old catch did not have comparible numbers so I just used the yellow one. Worked fine.