11070172000 Kenmore Dryer - Instructions

Watch the utube video a few times. Followed instructions. Marked all screws. Cleaned the inside of dryer where motor is. Replaced drum seal and then belt. I replaced front of dryer screwed everything in place and I did it. Holding drum in place while installing front of dryer was hard as it was heavy but I did it m. My friends and husband couldn’t believe it. Utube is great!

UNPLUG THE DRYER!!!!!
First removed the two screws holding the lint filter in place. Then slipped a screw driver between the top and the dryer body to remove the top. Using a nut driver removed the two screws holding the front of the dryer in place, remove the two wires for the door switch., lift the front cover of the dryer and set it aside. Support the drum ( two extra hands would be nice) and remove the drive belt. Then remove the drum. A thorough cleaning to remove all of the scorch like stain from the drum and back plate. Remove the seal and glue the new one in its place. Put it back like you found it. Make sure that the seal is not tucked against the back plate. Dryer works better than new and no more stains.

I suspected a faulty igniter and disconnected the cable to the igniter and measured the resistance of the igniter and found it to be 70 ohms then I checked the voltage at the same cable towards the power source and found it to be 25 volts ac which should be 120 volts ac. Next I checked the radiant flame sensor and found it to be open (it should be a closed circuit when cold). I removed the flame sensor (with the power off) using a small box wrench and found a broken lead. Replacing the flame sensor solved the problem.

I was reluctant to call a repair service. Typically when an appliance is as old as my dryer (14 years old), service people encourage you to replace, not repair. I had replaced the dryer's motor within the last 5 years and believed my dryer still had life to it. At first, I tried cleaning the lint build up from the dryer cavity and hoses. This worked but only for a couple of days. After reading other successful repair stories on the website, I decided to try replacing the thermal fuse. It was so easy. The part was easily identifiable. It was just a little hard to yank off the connecting wires. Good as new and no service call.

Replaced both Coils. Purchased M Series coils much less expensive buying coils together instead of seperately. Problem solved.

Removed lower front cover of dryer, located coils, removed old coils by disconnecting the wires and removing the hold down bracket screws. Pulled the old coils out replaced them with the new coils by aligning the index pins on the coils with the holes in the bracket then reattached the bracket and plugged the wires into the new coils. Then closed the cover on the front of the dryer. Dryer now ignites and stays on to heat up and dry clothes.

The most difficult part of this repair was making sure I purchased the right part !!! Part Select.com has a great website with pictures of almost every part you could ever need. I was able to select the right part and from there the repair was easy.

Took everything apart, replaced the igniter flint, and still didn't get heat. Then found out the thermal sensor wasn't running a electrical current through it with voltmeter and just replaced that, now it we have heat again!

I needed to remove the front lower cover, very easy as it is held on with clips only so I used a flat head screw driver to pop it off. I had to remove the lint filter and then there are two screws attaching the top cover of the dryer to the internal lint filter tray. The top of the dryer can then be opened front to back I again used the flat head screw driver to pop the top open as it has two clips at the front corners. It helps to have someone to hold it open or a rod of some type to keep it open. You can now lay the belt on the top of the drum and work it down the back side by pulling forward on the drum itself to seperate the drum from the seal that presses aginst the back side of the drum. I then went from the lower front to retrieve the belt now draped over the drum and pinched the belt to pass it through the tensioner and over the drive pulley. looking at it from the front the belt will come down the right side of the drum under the tensioner pulley around the drive pulley across the bottom of the drum and up the left side. The belt sits almost in the middle of the drum not against the back lip where there is a groove that might be confused as a place for the belt to ride that is where the seal sits then reverse the process to reattach the top to lint tunnel and reattach front cover and you are good to go . i would suggest vaccuming any old dust/ lint whlie everything is open as this reduces the chance for catching on fire I was supprised as to how much lint was loose inside the dryer cavity itself and our dryer is gas and the flame is an open flame.

Remove back panel n u can see the sensor and easy to replace thanks to the print out i was provided love this website

Shut off gas removed gas valve. Removed the coil retainer and installed the new coils. Reinstalled valve and checked. Found dryer worked fine.

My 80 series Kenmore dryer wouldn't start so I looked online for a solution to the problem. One of the sites I found stated that the problem could be as simple as a thermal fuse if other potential issues could be ruled out. I ordered the part on a Monday from PartSelect with standard FedEx ground shipping - stated it could be 3-5 business days. To my amazement, the part arrived the next day! Awesome!!! I watched the video on the PartSelect site to make sure I knew how to fix it, then followed the easy instructions. All I needed to do was use the nutdriver to remove the back cover from the dryer, unplug the two wires going into the thermal fuse, remove the old fuse, and pop the new one in. Then I just plugged the wires into the new fuse, replaced the cover and voila, the dryer worked like a champ! Thank you PartSelect for saving me a needlessly high repair bill!!

I had an issue where I was not getting any power to my ignitor. After replacing the ignitor with a fresh one, the problem persisted. Next, I went hunting all the fuses and therrmostats for continuity. All seemed fine. So finally I decided to jump the flame sensor which is located on the outside of the flame tube. WHALLA! It ignited the glow plug. So with one 1/4"" nut driver I removed the single bolt from the unit, then I used a pliers to remove the two wires from the old unit. I replaced the sensor with Tue new unit and all was well. It took less than 5 min once I diagnosed the problem.

I identified the correct catch of the three that were included in the package by matching its number to that on the old catch that I had pried out of the door using a flat screwdriver. I centered the new catch over the square hole in the door and pressed it into place. Then I used some needle-nose pliers to twist and remove the metal pin that fits into the catch from the main dryer housing. I replaced that with the new piece included in the kit, gently tapping it into place with a hammer. The repair complete, the door worked perfectly. Thanks for your help and for the speedy delivery of the kit.

Thermal fuse was blown so I replaced it. Still no heat. Hi-Limit thermostat and Cycling Thermo. had continuity as did flame sensor. Igniter tested 66ohms. I placed a wire jumper across the Hi-Limit and the igniter glowed, solenoids opened and gas came on. I orderd the Hi-Limit and since both "overheating" limiters were defective I decided to order the cycling thermo just in case. The Hi-Limit was received in 2 days but the Cycling Thermo was backordered. In the meantime my wife got antsy so I went ahead and installed the Hi-Limit and put her back in service... ...for one load. I wasn't certain if I had fried the "limiters" again but since they had continuity and I could measure continuity all the way to the Igniter I decided that it HAD to be the cause. I ignored the flame sensor since it never came into play without the igniter glowing... The igniter arrived and measured 56ohms. Hmmm... After installing the problem was solved. Word of advice: If the thermal fuse is blown and even if all else in the circuit SEEMS ok, go ahead and order the Fuse, Hi-Limit and Cycling Thermos, and the Igniter. It will take you about 30 minutes to install and you'll reduce your out-of-service time! Good luck!