11076995100 Kenmore Dryer - Instructions

I noticed my dryer was heating, but not tumbling. I"m a 53 year old single female, and my dryer I bought used 3 years ago. I had no clue what the problem was. I texted my brother and said, "it heats but doesn't tumble - is it shot?" He texted back "probably the drive belt - pop the top and see." So I popped the top, and sure enough, the belt was broken. So I googled "diy + dryer + drive belt" and watched a You Tube video. I then drove all over town looking for a belt, and the only place that carried it had closed at noon (saturday). So I googled " appliance parts + dryer and came to this site, ordered the part and it was delivered in two days.
I borrowed a nut driver from my brother, removed the front of the dryer, used a plastic cup to prop up the drum. I put the belt on the drum, being sure to place the ribbed side down, looped through the pulley and onto the motor, removed the cup, put the front back on, dropped the top, replaced the lint trap and the two screws holding that in place, turned the dryer on and voila! All done.

remove the front panel, belt [notice the way the belt is fasten] remove the tub, support bracket to the drum roller, and slide the new drum roller on and place the tre ring in the slot. then re-install everything in reverse

I didn't. Don't know how to get to light bulb to change it for this specific model

Took back cover off. Cleaned out the lint that had built up inside the dryer. Replaced the lint trap housing and lint chute seals. Also replaced the drying vent hose. Works great now.

Raised the top of the dryer then took the front of the dryer off. Took the drum off. Replaced the pulley and support rollers. Then, put the new belt on and put it back together.

Followed the instructions, removed the back cover, disconnected the top, disconnected the element and removed the element holder, then the element. Reversed procedure to install the new part.

After un-plugging the frig and allowing it to defrost, we emptied the frig and gave it a thorough cleaning inside and outside. I then removed the shelving in the freezer and the face plate at the back of the machine. One of the defrost heater coils had burned out and there was a loss of continuity which was keeping the frig from defrosting properly. The old heater snapped out easily. I went to this website and ordered a new defrost heater assembly which arrived practically overnight. It was identical to the old one and installed as quickly and easily as the original had come out. I put the faceplate back on, put the shelving back in, placed a thermometer inside the fresh food section, plugged it in and waited until I heard ice cubes drop. The fresh food section was holding at 41 degrees F which is optimum. The refrigerator has been working smoothly every since! Easy job!

Take out 2 philips screws in lint trap holder on top. Use flat screwdriver to pry up front left and right of dryer top near outside edges and tilt up out of the way. Remove 2 push-on AC connectors on door switch and remove plastic clip holding wires to dryer's front top metal edge. Remove (2) 5/16" sheet metal screw on inside top left and right edges to free up front panel. Lift front panel about an inch and it'll then pull off. It helps to have a second person to help hold or remove the drum at this point. It took 3 times for me to guess right on the squeak. First time I replaced the belt, second time I replaced these rollers, third and final time I replaced the idler pulley, the shaft of which had worn completely off so clearly i can't figure out how we didn't see (or hear) it the first two times! Dri-Slide lube helped stop the squeaking the first two times, but it always returned until this time, now I have a thoroughly rebuilt dryer for the next generation! (PS vacuum out the bottom of the dryer while it's open to remove both lint and greasy roller shavings - do this FIRST and you'll have cleaner hands & clothes!)

Removed rear panel, removed 3 screws and old element and installed new element. To install new element I only needed one screw and spliced in the two wires that were provided with the element. This repair was simple and now the dryer works great.

My dryer started squeaking and I thought it was the drum rollers, so I bought a set. When I attempted the repair and got as far as removing the dryer drum and I decided to spin the shaft on the motor and that was where the squealing was coming from. I put the rollers on and reassembled the dryer. One day later the motor seized up. Ordered a new motor and installed it with no problems. The nut on the back of the motor ended up being a 20mm wrench. Motor cost me $105.56 and the maintenance kit (ps37308) (2 rollers,4 clips, button clip, new idler pulley and belt) cost $32.08. It cost a total of $137.64 in repairs with no labor costs and I accomplished it in under an hour. Minor handyman skills needed or find a friend who is handy. My dryer is 14 years old and now is running like new again. I used the 50% rule, if a repair exceeds 50% of the cost of a new machine, replace it, if the repair can be done for less than 50% of the cost of a new on, fix it.

Just put the knob on where old knob was.

i took the old knob off, went to partselect and ordered the part really easy as their site helped me find the correct part, and put it on with ease when it came in the mail. It works great and PartsSelect helped me be a hero to my wonderful mom. Thanks.

I opted to remove front, top and back panels. This is best done with dryer laying on it's back so drum remains in position. Hold panels and pieces in place with masking tape (2") You should block up the dryer so you don't damage the gas pipe. I opted to total shop vac out the piece and lubricate the rollers and tension pulley. I made more in change than the belt cost!

Overall an easy repair. Belt came with diagram for easy threading the belt.

I unplugged the dryer from the electrical outlet, removed the back of the unit and checked the heating element for continuity. There was no reading. I then removed the housing and heating element and visually inspected it. The coiled wire was broken in two places.
I then did a Google search with the model number and found Parts Select. I placed my order Sunday afternoon and the part arrived the following Wednesday. That evening it took about 20 minutes to install the new element,put the back on the dryer and re-attach the exhaust tube.
The old dryer is as good as new again.
TJ in Boise

Ordered the motor with pulley and blower wheel in case the wheel did not come free from the motor.
Took out the lint screen, took off the top and disconnected the wires for the door switch, took off the front.
Remove the idler poi and the belt and then removed the drum.
I read in other repair YouTube videos, the blower wheel sometimes is so seized onto the motor axle that you have to remove the wheel by cutting it off.
Yes, ours seized!
Cut off the motor axle with a hacksaw and then the motor and the wheel were free. This was not an issue since I had purchased both the motor and the wheel which I recommend doing anyway. Our dryer over 25 years old and it does not have many electrical components, which I love. We removed the parts put in the new parts. Follow the wiring diagram to get the new motor hooked up.
Then I replaced the drum support rollers, which were a snap and then we put it all back together.
We added an extra step because we had to takeoff the back of the dryer to gain access to the blower. It turned out to be a good thing since years of lint have been trapped at the bottom of the lint chute.
I cleaned everything, washed everything and put it all back together and it purrs like a kitten.
Took us about 2 1/2 hours total since we are very cautious and slow as we didn’t want to break things.
I am very happy with the end result and hopefully it will last another 25 years!
Parts were spot on and worked perfectly.
Much more economical than buying a new dryer for $750-$1000.