11073024102 Kenmore Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Nick from Brandon, FL
- Parts Used:
- WP3392519
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver
No power
My 14 year old son did it as I supervised! Pulled the dryer out on a dolly, unpluged the dyer, removed 9 hex head screws to remove the back cover, removed and replaced the thermal fuse, located next to the exhust outlet, set the cover back on, moved the dryer back in with the dolly. I had the thermal fuse over nighted to me for a total price of $35, figured I saved at least $150 on a service call by Whirpool.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- FRED from BRIELLE, NJ
- Parts Used:
- WP338906
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Gas Flame Would Drop Out
First it was a process of alimination to find out why it was dropping out. After the problem was found it was just a matter of replacing the holding coil on the gas valve. Thank you fred kenney sr
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from TAVARES, FL
- Parts Used:
- 4392067
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
high pitched squeaking noise when dryer is first started.
1. Disconnect dryer from electrical outlet. 2. Pull dryer out and disconnect the exhaust tube from the back. 3. Remove the screws at the top of the dryer back ( 3 ) and remove the top of the dryer. 4. The service instructions will be in a bracket on the top right. I didn't use them because I have done this job before. 5. Continue to remove the screws holding the back to the sides. There will be a lint collector attached to the back panel by three screws. This must be removed first, then the screws along the edge of the back panel. 6. Pull the back panel up and away from the sides and set aside. You will see two lower rollers attached to this panel. 7. Look under the drum and you will see a idler arm and roller in front of the electric motor and a little to the left. Notice that the drive belt is looped around the roller. Unloop the drive belt from idler and roller. 8. Lift the drum of the dryer up and out of the dryer. 9. Replace all the rollers (4) by removing the plastic "star" on the roller shaft. This can be done using a small screw driver. 10. Once the rollers are replaced, place the new drive belt, ribbed side facing the drum around the drum. Lift the drum up and into the dryer enclosure, making sure the rollers in the front of the drum are in the ridge groove. 11. Lift the back of the dryer in to the dryer enclosure, again making sure the rollers are in the rear groove. Turn the drum by hand to make sure the front seal is flush to the front of the dryer and that the front rollers are in the front groove. I2. Install drive belt around electric motor shaft ( ribbed side facing the shaft), lift idler arm up while running the non-ribbed side of the belt around the roller on the idler arm. 13. Install the back panel using the remaining screws. 14. Install the top of dryer by sliding it into the front panel and securing with the last three remaining screws, these 3 screws go on the top of the back panel. 15. Replace exhaust hose and replace dryer into space it formally occupied.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michelle from Richardson, TX
- Parts Used:
- 72017
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Scratches in Surface
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wiliam from Belleville, MI
- Parts Used:
- WP3387134
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Dryer would not shut off on auto dry settings
I removed the discharge duct from the back of the dryer. Then, I removed the screws on the back of the dryer and the back itself. This exposed the cycling thermostat. I removed the screw holding the thermostat. I took the wires off the defective thermostat and reinstalled them on the new thermostat. Then, I reassembled in reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Tucson, AZ
- Parts Used:
- WPW10314173, WPW10359272, W11236646, WPW10512946
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
worn out part
The repair was fairly easy. The most timely part of the repair was removing the twelve screws from the back panel to expose the repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Grace from New Smyrna Beach, FL
- Parts Used:
- WP3977456
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
push to start switch was not working
Removed the old one and installed the new one! What impressed me the most was the amount of time for delivery, one day! Actually it came before 24 hrs!!! Very impressive! I would highly recommend this company!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bill from Houston, TX
- Parts Used:
- 279570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dryer door catch broke
The old catch on my dryer door was gone and I was keeping the door closed using tape. I ordered the part and it arrived with no hassles in about 5 days. The repair was too easy. I just popped the new catch in place. It took all of about 30 seconds to complete using no tools. I wish all home repairs were this easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Princeton, WV
- Parts Used:
- 279640
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
TOb stopped turning after a week or so of high pitched "squeals" coming from inside the dryer.
I recommend you order the idler pulley as soon as you start to hear the unusual noise indicating metal against metal. Replace the idler pulley before it fails and possibly causes more damage to the drive system. Simply removed the power cord at the back of the dryer and then the multiple screws holding the back panel in place as well as the clip holding the exhaust vent in place. You may need to remove the top panel to access a few of these screws. A diagram of the belt routing is in the paperwork I found behind the front lower panel of the dryer. This too is easily removed with just a few screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- john from goldsboro, NC
- Parts Used:
- 661570
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Dryer not spinning
I took off the front panel via 2 screws on the inside of the dryer with the top panel in the maintenance position. Pulled out the tub(cut my hand pretty bad in the process but continued). Did some cleaning and I had to google how the belt tensioner goes into place. Rather difficult on your own i held the belt and placed the tub back into place while placing the belt around the tub putting it in the correct area. thats pretty much it and began reinstalling the parts i had removed.. easy fix now that i have done it once. This is all after my landlords said they werent replacing it and just to have this one hauled off, so all in all i have a 26 dollar dryer now:)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roger from Bonners Ferry, ID
- Parts Used:
- WP338906
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Dryer would not heat up.
I unplugged the dryer,removed the two small screws on the front of the dryer and pulled the bottom forward. The two wires connected to the door do not have to be removed. With an electrical tester using the Ohm setting I tested the Radiant sensor and the Gas Valve coils. The two terminal coil was DOA. The dryer can be operated with the front open as long as the door wires are connected. Symptons: The igniter would heat up and not release gas. My repair was successfull due to this awesome website and the super fast shipping service. AAAA++++
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sara from Solon, IA
- Parts Used:
- W10120998
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Felt piece coming out of filter
Removed old filter and put in new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- joe from cheswick, PA
- Parts Used:
- WP697772
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
craked blower motor
somthing fell down in the blower motor compartment and busted up the bloewr motor fan,and was making noise and out of balance.i changed the blower motor and runs like a charme
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Maricopa, AZ
- Parts Used:
- WP3406107
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broken door switch
Followed your online video for disassembly and it was not only educational but actually quite simple. I would recommend that you start the video with," make sure the power cord is disconnected from the power source". I have worked on numerous pieces of large electrical equipment and would strongly suggest this be added. Some people think if it's, "off", it's safe. Your phone staff when ordering was great. We will do business again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christy from Riley, MI
- Parts Used:
- WP338906
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Dyer would not heat, flame would shut off within 10 seconds
I opened the panel, undid the plugs, detached the radiant sensor by undoing one screw and removed and replaced the part. Fairly simply.
Was this instruction helpful to you?
Thank you for voting!