1106927450 Kenmore Dryer - Instructions

Jimmied out the latch using two screw drivers to get under the edges. Pushed the new piece in. Voila! Took 2 minutes for what my repair man told me would cost about $200 to fix. Unbelievable!!( I first watched some YouTube videos to get the idea )

Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

The original lint filter was broken, as the dryer was very old I did have the part #, I searched the internet I saw partselect.com on the search engin I did know it would be so easy to get this product, I selected the part by size specification.

Thank you partselect .com for making my life easy. Or else imagine me driving around looking for stores which sell spares for old dryers wasting time and gas-go green shop at home.

re-placed screen

pulled out the old one and put in the new one. I wish all repairs were this easy. I also had to reattach the vent hose, which is annoying because I'm the only one who fits behing the dryer without disconnecting the gas. I never touch the gas related parts.

I appreciate how easy your website made it, to get the parts, I would recomend this site and will be back myself.

Replaced roller. Very simple. Dryer is the easiest appliance to repair. Only a few parts keep a dryer working

lifted top section of dryer
removed front dryer panel
removed drum belt and tensioner
removed both drum rollers
cleaned both roller axles
installed new rollers
reassembled remainder of dryer
if you are at all mechanically inclined, it is a simple job

Disassembled dryer, removed tumbler, replaced drum support rollers

1 Vice grips are required to remove the fan/blower. Clamp on inside of dryer so you can remove the blower/fan assembly

Recommend 10" or larger 14" will definitely do the job

2. Blower/fan is reverse threaded when facing the back of the dryer. That is how I broke mine. Turn clockwise to loosen - feels very unnatural

3. If you have to replace the 5 & 6 electrical connectors, you have to have a barrel crimper for insulated terminals - IWISS SN-02C RATCHET TERMINAL CRIMPING PLIER TOOL, 24-14AWG is a good example

I first tried replacing the Radiant Flame Sensor, which was located in a tight space and was very difficult to access. I finally gave up and called a handyman to replace it. That didn't fix my problem. I needed a new igniter. That was easy to replace, but it's fragile and I broke the first one...

After identfying that the problem was due to a damaged drum support roller, I decided to replace the bad roller instead of replacing the dyer itself.

The first thing was to remove the front cover
and the front panels to expose the drum. (Only a few screws hold them in place.) Next, the drum was removed by first releasing the belt from the motor pulley and tensioner, and then pulling the drum straight out.

At this point the two rollers would be exposed. The triangular plastic retaining locks were removed by slightly prying them off. The old rollers were then removed and replaced.

Before putting everything back, this was a good time to vacuum all the accumulated lint inside, especially the lint that had accumulated around the motor assembly and the fire box.

(A pleasant surprise: I found a lot of coins inside the unit, enough to recoup half of what I spent for the new rollers.)

The hardest part was figuring out how to access the dryer mechanism. This Amana dryer has a lower front panel that is removed and not the top. There are few instructions available for this configuration. Then the part locations do not resemble the video instructions for trouble shooting. I discovered the broken part because when fiddling with the wire connections the metal tab disconnected due to fatigue or corrosion. Removing, identifying and replacing the flame sensor was quite simple. The dryer now works as before. The dryer is 23 years old. The most time in this repair was spent figuring out how to disassemble and identify a different configuration than in the videos.

Removed 2 screws holding the lint trap on top, popped up the top and lifted back, removed 2 screws on the inside top of front panel, lifted front off and set aside then reached under the drum and pulled tension pully to loosen the belt, and removed the drum. popped the motor clams off and then used 2 adjustable wrenches to grasp the nuts at the front and back to remove blower fan. When you look for the area in back to loosen the blower fan you may notice the nut that you are looking for is actually part of the fan and is plastic looking rather than metal. I did have to take off the back cover to the blower fan to tighten it back up.I had seen instructions that the blower fan would have a 3/8 hole in the back of it to loosen it,but mine did not. I assembled it and it works great with my new motor and rollers. I received my part in 2 days, very happy

I ordered the part(and a backup) and had it in two days. 5 days less than ordering from sears.

Removed the drum then removed the old parts and installed the new ones. Dryer now runs very quite and heats good. You have very fast service my mother ordered the parts on the net one day and I received the parts next day and did the repair that night and dried clothes. Thanks,

Your great service is very hard to find.