1106508935 Kenmore Dryer - Instructions

My husband figured this would be an easy fix....until he realized the part he had turn to remove the motor was made of plastic and was basically welded to the fan, so needless to say, we are now also replacing the fan....once the fan was loose, it was very easy to put in the new motor and fan and reassemble the dryer...good luck and watch out for those plastic moving parts!

Read earlier posts on the change out of motor with times varying from 30min to days. My ordeal was in the days category. Long story short, I could not get the blower off. The back of the blower has flats to use a adjustable wrench and you can use a socket on the back of the motor. I rounded off the flats on the blower and had to cut it off. Since I had only ordered the motor, I had to then order blower. If you can get the blower off the motor is about a 30min to 1 hr job. I would suggest purchasing the blower along with the motor to save some time.

I took the back off of the dryer and then removed the lint chute assembly. Next came the top removal which was a little tricky because the top locks were installed incorrectly from factory. After about 20 minutes for a 2 minute job, the top came off. Now I was able to remove the front and the drum. This left me access to the motor. The hardest part of the whole job was removing the blower wheel. Being made of plastic you must be careful not to brake it while grabbing hold of it and applying torque to the motor side. This process takes two people. My wife helped me and it took about 5 minutes. Leave the motor mounted for this. Once the wheel was off, the motor was then removed, the new one was installed and the process was reversed for assembly. Not very difficult overall and saved me a whole lot of money. Make sure you vacuum out all of the dust since you have the whole dryer apart. It will probably be the last time you see inside it and the dust sure builds up inside after 12 years! Thank you Partselect!!

First I removed the rear panel of the control sectio and the main rear panel. I checked the switches and fuses. The fuse for the dryer vent was giving an intermittent signal, so I replaced it with one I picked up at a local repair shop.
Since I had started working on it, and due to the age, I went ahead and ordered a motor, belt, and drum rollers and replaced these as preventive maintenance.
Once you realize how everything comes apart, it is not a very dificult job to overhaul the complete dryer.

drilled a 7/16 diameter hole directly in the center of the two mounting holes filed it square big enough so as the spring tip fits thru now the door closes on the spring which actuates the switch looks and works perfect.

When I ordered the part, I viewed the installation video. That was a key step for me. It told me how to identify the correct part (there are multiple latch pieces in the repair kit, and one of them matches the type of door for the dryer), and how to disassemble the door to get the part installed. When the part came and I installed it, it turned out that I could snap the part in by hand, with no tools. It took about 5 seconds to try it, and it worked.

The dryer just stopped after a new load of clothes was put in. It appeared to be a power problem as there were not warnings, it just stopped. After checking the power, I suspected it was an electrical interlock problem. After nosing around, I traced the power to the dryer door interlock. Sure enough the switch was fine, but the mechanical lever was worn away. After Googling around for a replacement I found PartSelect.Com. Found the part, ordered it, and I am back in business. My wife is not happy though, as she wanted a new dryer:)

Reviewed the video showing how to remove the bad-order part and install the new part. No problem. Installing the new part was exactly what was shown in the video on the web page.

Unpluged power cord.removed top and front pannels(after disconnecting wiring to door switch.) Removed drive belt to drum,and removed drum. Checked and marked motor wiring before disconecting from motor.Removed motor,After unscrewing the blower from shaft.(Had to remove jumper wire from motor)Reinstalled the blower and secured the motor,reconect wires to motor.(rechecked wiring connections)Put back the drum,drive belt,and the front door pannel.(reconect door switch wiring)then the top pannel.Plug in the power cord and checked opertion.....WORK'S JUST FINE! I ordered the replacement motor on a sunday,and the new motor was setting on my kitchen table tueday afternoon when i got home. Great job" PARTSELECT."

Repair was simple, minus pulling the drive motor shaft out of the back fan. The female end of the dryer fan was made of plastic, so the socket wrench cracked the plastic end. Other than that, the repair was simple and easy to do. Much better paying the $88 for a new motor vice paying $400 or more for a new dryer. Dryer has run like a champ since replacing.

I used you-tube to troubleshoot and repair. Your part store was excellent to deal with. Delivery was prompt and cost was very reasonable. Thanks!

i watched the video from Part Select. did exactly as seen and presto it was easily done. never could've done it without Part Select.

Screwed in light bulb and glass protector

very easy

Loosened two screws in back top of drier and pulled forward and up to hinge top of drier and allow access to door switch.Took out broken actuator spring and replaced with new one,snapped lid back in place and put screws back in hinges and job was done.