1106908610 Kenmore Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- James from Richmond, VA
- Parts Used:
- W10820036
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
water wouldn't run out of washer
Two screws holding top, unhook wire conector. remove cabinet,replace switch. Reassemble.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Laszlo from Vienna, VA
- Parts Used:
- WP691581
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Door switch actuator spring broke
Disconnect dryer.
Unscrew the two screws that hold the door actuator assemby.
replace broken spring.
Screw the the two screws back.
Unscrew the two screws that hold the door actuator assemby.
replace broken spring.
Screw the the two screws back.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Victoria from Roslyn Heights, NY
- Parts Used:
- W10820036
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Dryer would not start.
My dryer is 35 years old and thought this was it, but I googled the question and found out it was the door switch. Orderd the part and received it very fast and didn't want to wait for my husband to come home so I went on you tube and found a video how to open dryer and change switch. I did it in about 30 min. and yes it is now perfect again. No problems. I just unscrewed the old switch and put the new one in. Maybe I'll get another 35 years out of this machine. :o) Thanks for making it so easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- katherine from Salem, OR
- Parts Used:
- WP691581
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
metal spring in door broke the peice that allows the drum to spin
This was rather easy to fix. I had never opened the dryer before but had a serviceman come out so I knew that you can pop the top of the dryer off by putting a flat edge screwdriver in between the top and bottom and popping up. You must remove the screws from the lint dryer before so the top comes off. The piece to replace had two screws and that was it. To get a repairmen from Sxxrs where we purchased it 15 years ago they charge a flat fee of $75 just to come out. That does not include the repair just a fee to come and tell you how much more it would cost to fix it. I ordered the part for less than $5 and $12 more for 2-3 day delivery! What a bargin! I was back drying clothes 15 minutes after the part arrived! Very happy that the part is still being made!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Cape Girardeau, MO
- Parts Used:
- WP691581
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Dryer wouldn't restart when start button pressed
Before beginning, unplugged dryer. 1) Used putty knife at each front corner of top to pop lid loose from clips. 2) Removed hex screws at back of control panel to allow lid to tip open. 3) With lid opened, removed hex screw from inside-top of each side to allow front to pull open from side panels and access door switch easily. 4) Removed clip that holds retaining wires from top. 5) Pulled wire from each side of door switch. 6) Removed switch assembly using Phillips screwdriver to remove two screws mounting switch at top of door opening. 7) Removed broken actuator spring and replaced. 8) Reversed process to reassemble.
Was this instruction helpful to you?
Thank you for voting!
Blower (fan) assembly and old model motor with different electrical connections
1 Vice grips are required to remove the fan/blower. Clamp on inside of dryer so you can remove the blower/fan assembly
Recommend 10" or larger 14" will definitely do the job
2. Blower/fan is reverse threaded when facing the back of the dryer. That is how I broke mine. Turn clockwise to loosen - feels very unnatural
3. If you have to replace the 5 & 6 electrical connectors, you have to have a barrel crimper for insulated terminals - IWISS SN-02C RATCHET TERMINAL CRIMPING PLIER TOOL, 24-14AWG is a good example
Recommend 10" or larger 14" will definitely do the job
2. Blower/fan is reverse threaded when facing the back of the dryer. That is how I broke mine. Turn clockwise to loosen - feels very unnatural
3. If you have to replace the 5 & 6 electrical connectors, you have to have a barrel crimper for insulated terminals - IWISS SN-02C RATCHET TERMINAL CRIMPING PLIER TOOL, 24-14AWG is a good example
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Colorado Springs, CO
- Parts Used:
- WP694089
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Screw drivers
Fan blade had to be removed , was broken off from motor.
Had to completely dismantle the dryer including the motor and grind off the.bolt holding the fan blade on. I did not realize it was threaded on with a left hand thread.Then reassembled.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robbi from PowderSprings, GA
- Parts Used:
- 341241
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
The dryer would not tumble
I watch the video and played it again while I was working.
I am a 54 year young woman and I did it.
I am a 54 year young woman and I did it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeffrey from South Amboy, NJ
- Parts Used:
- 341241
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Worn Out Drive Belt
Pull dryer out from wall about 6 to 8 inches step 1 - romove front/bottom access panel. Step 2 - remove lint trap and remove 2 screws (philips type) that is under lint trap door. Step 3 - push in 2 wood shime in front edge between lid and front panel (angled shims like door shims - a putty knife will work to, just be carful not to scratch finish) step 4 - fold lid upward and back (like on a hinge) step 5 - looking from where the bottom/front acces panel was losten 2 screws - one left one right about 3 turns - 9you can remove them it just makes it easier to reinstall the front panel. Step 6 - find appropriate pot or stacked 2 x 4 pieces - something to hold up the drum when you remove th front cover, and from underneeth support the drum. Step 7 - look thru bottm front access hole - there are 2 springs that come down from the door - and clip onto the frame of the fryer - unclip them and place on the side. Step 8 - remove 2 upper screws that hold front panel on, and remove front panel, if you left the bottom screws attached but loosened you have to lift up on the front panel a bit. Step 9 - looking from the bottom thru where access panel was - you will see motor on right with a additional roller (tensioner) - push upwards on tensioner to relieve pressure on motor and pop off belt (remember where tensioner is and how it clips in to base. Step 10 - work belt off of drum towars front - to remove it all the way you will have to lift up the drum slightly off of the pot or whatever you used for support so the belt can clear. Stem 11 - new belt goes on the same way you took to old one off - plat side away from drum with ribs against drum. Step 12 - again lift up on drum and work belt back on. Step 13 - tricky part is how to get the belt back on the motor - prentend you are threading a needle wht a folded over piece of thread - hold the belt with about a 4" loop with your left hand - hold up on tensioner and feed it back thru and work belt back over end of motor pulley, after front panel is back on with the 4 screws tightened spin the drum and make sure belt is between the 2 lines marked on the drum and remove the pot or whatever u used to prop up the drum. Dont forget to attach the springs for the door assemble all other components in reverse order. And dont forget to take the pot back out
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Monique from Roosevelt, NY
- Parts Used:
- 341241
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench set
dryer turned on but did not tumble
I removed the lint trap then the dryer cover from top and front side. I placed the belt around the dryer drum being sure to put it on the correct side with the grid side against drum. I coiled the belt around the pulley and motor tract. Replaced everything in opposite order in which it was removed.
Video from website was very informative and helpful. I was able to follow along step-by-step to replace the dryer drum belt. I am officially a do-it-your-selfer!!!
Video from website was very informative and helpful. I was able to follow along step-by-step to replace the dryer drum belt. I am officially a do-it-your-selfer!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- bruce from east waterbrough, ME
- Parts Used:
- 341241
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broken Multi Rib Belt-92-1/4''
I took the back of my dryer off to see if the problem was there. I saw that the belt was broken and laying on the inside of the dryer. Took belt and went on line (Google) my KitchenAid Dryer from it's model number. The website was PartSelect. Found the belt I needed and saw a video on how to replace the belt. I called to order the belt and spoke to Steve, which help me with all my needs. Steve knew just the belt I was looking for and placed my order. The belt arrived a few days later. While I was waiting for the belt to come in, I removed the front of the dryer and get ready for reinstall. It took me about 15 minutes to install the belt and put the front of the dryer back together. I found PartSelect to be very helpful and saved me, maybe $150.00 by not having to call a serviceman to do the easy replacement. Thank you Steve and PartSelect, now I'm number 1 with the wife again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Damon from Somerville, MA
- Parts Used:
- 341241
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Dryer belt broke
Removed the two screws at the back that hold the top of the dryer. Then I pried off the top at the front by inserting a screwdriver into the front to remove the top from the clips. Then I tilted up the top like a car hood.
I removed the two screws inside that held the front on and lifted the front off. Because of the wires attached to the front, I made sure to turn the front aside without pulling on the wires. After removing the broken belt, I put the replacement belt over the front of the drum, lifting the drum a little. Then I threaded the belt over the drive and around the tension wheel per a diagram I found on the web.
While I had the front off, I removed the lint trap and cleaned out probably decades worth of lint.
Then I replaced all the parts in reverse order, plugged it in and had a working dryer!
I removed the two screws inside that held the front on and lifted the front off. Because of the wires attached to the front, I made sure to turn the front aside without pulling on the wires. After removing the broken belt, I put the replacement belt over the front of the drum, lifting the drum a little. Then I threaded the belt over the drive and around the tension wheel per a diagram I found on the web.
While I had the front off, I removed the lint trap and cleaned out probably decades worth of lint.
Then I replaced all the parts in reverse order, plugged it in and had a working dryer!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edmund from Cranston, RI
- Parts Used:
- 341241
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
I had a problem with the drum when installing the door
I pried the top of the dryer with a screw driver and then lifted the top of the dryer, I then removed the two screws "with a nutdriver" that held the door in place and then removed the door and drum. I then got the new belt and placed the belt over the drum and positioned the belt through the idler arm and then on the motor pulley. I had to hold the door and drum to lock the bottom of the dryer door to the dryer and then made sure the rear drum seal was in place and the belt did not slip off the motor pulley
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Erika from Swarthmore, PA
- Parts Used:
- 341241
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set, Wrench (Adjustable)
Dryer drum wouldn't turn
First, I unplugged the dryer. I pulled up the lint filter, then unscrewed the two screws there. Then pulled up the top panel. I had a helper hold it up since it couldn't lean against the wall. Then I had to take the front panel off the dryer. The idiots at Kenmore used screws, not pins, so I needed to use a socket wrench to get those two out of the top corners. Then I lifted it up and off. I removed the broken belt. I put in the new one. I replaced the pulley, which had fallen without the tension of the belt holding it in place. It was pretty easy to figure out how it went, but I consulted the online community for a diagram. I threaded the belt in place, replaced the panels, and viola! It worked. Easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Allen from Valrico, FL
- Parts Used:
- 341241
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Broken belt
It was easy to remove the lint trap first, then the front dryer panel. The drum easily was removed and installing the new belt was a little tricky because the belt had to be mounted onto pulley while holding the drum in place. I had a little help from a friend to help me stabilize the drum as I placed the new belt. Once on, it was easy to re-install parts in reverse and have dryer working again.
Was this instruction helpful to you?
Thank you for voting!