11086879800 Kenmore Dryer - Instructions

replaced internal dryer filter housing

I first watched the helpful video on website. Un- plugged the dryer. I removed the back cover and tested the thermal fuse with the multi meter. Ordered the replacement part. Replaced the Thermal Fuse, and put the back cover back on. This was a very easy fix! It takes longer to remove the back cover of the dryer than it does to replace the fuse. While I had the back cover I used my air compressor to blow out any lint. This dryer is as good as new now. this site fast shipper, Great website.

Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

removed the rear panel to gain access to the internals of the dryer, removed the one screw that retains the fuse, out with the old and in with the new.
delivery of the part was 2 days sooner than expected.
could not have been a simpler process!

The numbers on the metal plates were the JC Penney numbers - that no one recognizes. I eventually found the model number inside the timer case on a printed schematic. I started by disassembling whatever metal covers were removable by finding sheet metal screws and unscrewing them. If you pull on the sheet metal covers, you can find where they are connected to the frame. Eventually, I found that both the heating element was broken and the thermostat was fried. It took a while looking at various websites to find the proper parts. It's all OK now.

Had to replace the rear felt seal and the motor. It was no problem to find videos on how to do both of these repairs. Took apart the appliance. When the parts came first replaced the drum rear felt seal and waited for the motor to be delivered. Then replaced the motor as per online instructions. Also went to Home Depot to buy a new flexible dryer tube since the old one had a few holes. It works perfectly again.

First unplug appliance, Remove dryer top and front. remove drum and belt. Two clamps hold motor in place. remove them and lint chute housing in rear, exposing the fan. Use vice grips to hold motor shaft behind belt pulley flat spot. Remove fan, it's reverse threads. A large adjustable wrench on plastic fan nut and spray lubricant if very tight. Place new motor next to old and switch wires over, crimp on new 1/8'' connectors. Remember the green ground wire may need an allen wrench. Put back drum,belt, lube the rollers and replace back cover, front, top.

Unplugged stove . Removed floor of oven . Easy . Removed the ignitor ,near back of stove under removed floor . .Left it in place to enable locating where wire came through back of stove . Pulled the stove away from wall . Removed back panel of stove . followed ignitor wire to its plug in position . Returned to the front of stove . Inserted new ignitor wire through back wall of stove . Went behind stove , pulled wire through enough to plug new ignitor into proper position . Put back panel onto stove . Pushed stove back against wall . Went back into oven to screw new ignitor into place . Replaced oven floor panels . Put cooking racks back in . Wife proceeded to bake once again .

I watched a U Tube video about banging sound from dryer. Once I recognized the problem, lifted the top, removed 2 screws holding the front, removed the drum, and bingo. Saw the worn out drum roller. Ordered the replacement parts from "PartSelect" on line (Great Company). Was in no hurry, so I chose regular mail delivery. 4 days later, got the correct replacement parts, put the dryer back together, and now, the dryer is quieter then when I bought it new, a thousand years ago. I will never again be afraid to tackle an appliance issue. THANK YOU !!!

Unplugged dryer, unscrewed back, and replaced fuse. Easy as 123. Video showed what to do step by step! I am not a handy man, just a woman trying to be money5 smart. Anyone could do this and save on home repairs.

Turn off Gas, unplug electric cord, remove rear cover, remove two screws holding the lint trap to the top, raise top flip[ping to the back supporting it not to damage wiring, remove bottom front cover, remove door springs, remove front cover, disengage belt tensioner, remove drum. unclip right side roller and remove, unbolt left wheel mount from the rear and the bracket in the front, remove clips or cut off (new ones come with new clips). clean the wheel shafts, light sanding if needed, apply light coat of lithium grease. replace wheels and reassemble dryer in the reverse order from disassemble. roll drum by hand after front back on to ensure it rolls without catching. Finish and test.

I follow the instructions from the video you guys show the only issue is putting back the tensioner in place but my brother leaves next door and help me.

removed cover then pulled wires with a plier, unscrewed the fuse and installed new fuse then put back cover plugged in power cord, fired dyer and run dryer for 2 minutes and felt warm air coming out of the exhaust.

I removed the back of the dryer, removed the single screw holding the fuse in place and checked it for continuity. It didn't work, so I placed an order and 3 days later I was back in business. the replacement took about five minutes.

Two screws holding top, unhook wire conector. remove cabinet,replace switch. Reassemble.