Models > 1106818610 > Instructions

1106818610 Kenmore Dryer - Instructions

Jump to:

All Instructions for the 1106818610
121 - 135 of 462
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Jon from LaGrange, IL
Parts Used:
279827
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
dryer stopped and smelled of smoke.
I reviewed several videos on parts sites and YouTube. There is more than enough advice online showing step-by-step instructions. The only difficulty came with the rear nut holding the motor shaft to the blower fan. I used a crescent wrench with a long pipe over it for added torque. The two spring clips holding the motor in place can be removed and installed with the help of a nutdriver pushing the clip down, . The dryer was new enough so the motor needed no switch changes. The new motor is running fine.
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
John from Livingston, LA
Parts Used:
WP4391960
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
Clothes took forever to dry
Basically, the stories listed on your website had excellent instructions. The important thing to remember is popping the top to get to the upper housing clip. Otherwise, a person might try to pull the element out from the bottom of the housing, which would be a minor disaster. I'm very happy with PartSelect and the website. I'll be back!
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Cathy from Benson, MN
Parts Used:
WP4391960
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Wrench set
heating element went out on my dryer......the coil snapped.
Pulled out the old element (by removing the two screws that hold it in place) About a couple of inches and disconnected the two wires. I then inserted the new element and screwed it in place and connected the wires. Just took two of us to fix the problem...one to tilt the dryer forward and the other to put in the element.
I am so happy I didn't have to go out and purchase a new dryer........new ones are way too expensive!
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Frank from Union Beach, NJ
Parts Used:
279570
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
The door whould not close enough for the dryer to work.
Got my parts very quickly.
Popped out the old door latch with a screw driver and pressed in the new one.
Very simple.
Thanks Parts Select.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Kim from Northridge, CA
Parts Used:
WP691581
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
dryer wouldn't turn on
I removed the two screws on the top by the lint catcher. Then, per information from this website, I pried up the top. I reached down into the dryer and removed the two screws on the broken door switch and replaced it with the new part. I am a recently widowed, 55 year old and was thrilled to find good advice, information and instructions on your website!! Simple as could be!
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Theodore from Tyler, TX
Parts Used:
279570
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
dryer door wouldn't catch, catch was broken
took the cstch reciever out, with my fingers, pushed the new one in, snap lock fit.......couldn't be better, like repairing a model T ford.......
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
thomas m from sacramento, CA
Parts Used:
WP4391960
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
dryer quit drying
tested the heating element with a multimeter and got no reading.ordered and got the part (3 days flat,excellent).removed a few hex head screws in back to drop the panel,popped the top with a putty knife,removed one screw to release the heating element housing and one more for the element.reversed the procedure and dryer is up- and cooking.could not have been much easier.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Michael from Goddard, KS
Parts Used:
279570
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
broken door catch
the part fit perfectly, it just snaped right into place.
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
DONNA from SAN LORENZO, CA
Parts Used:
279570
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
catch was missing to close dryer door
The only thing I had to do was hammer the catch inside the square fitting and presto it was done. It took me less than 3 mins. I thought I might of needed instructions, but it was really simple. Even a guy can do it. (smile)
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Diana from Canfield, OH
Parts Used:
279570
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers, Wrench (Adjustable)
dryer door won't stay shut
I replaced the male end first hoping that a change in the female part would not be needed. Unfortunately no. I used needle nosed pliers to pry the male part out and pushed the new part in. The female part of the door catch was more difficult. I didn't do it in "textbook" form, but got the job done with pliers and a screwdriver. Worth every penny to fix correctly instead of rigging it. Do it!
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Gregg from St. Augustine, FL
Parts Used:
279570
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Dryer door would not stay closed
After removing front door panel (2 screws) I removed the old latch catch and replace with the new part. 4 minutes later, the door was back together, the dryer was running and the door was staying closed.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
ronald from PICKENS, WV
Parts Used:
339392
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Old filter handle broke
replaced filter
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
ROSEMARIE*SALVO from BRONX, NY
Parts Used:
339392
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Handle on lint filter cracked and came apart
Opebed lint filter door, removed old lint filter and replaced it with new one.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Mark from TERREBONNE, OR
Parts Used:
WP691581
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Machine would not start and light stayed on with door closed.
Turned off circuit breaker to machine. Removed lint trap to allow removal of two Philips screws from vent passage that hold lid on. Opened door and removed two Philips screws that hold switch to front of machine. Using flat blade #2 screw driver pushed on plastic locking tabs under front of machine top about 2" in from either side to allow top to be lifted up from machine. While holding up at 45 degree angle reached in and grabbed switch to pull it out for easy access. Set top down gently once switch was out. While holding switch removed broken switch actuator and installed new actuator on to switch. Lifted top back to 45 degree angle and with left hand held switch assembly in place and started two screws previously removed back into actuator holes. Tightened screws snugly. Lowered top back into plastic locking tabs and gently pushed down to secure top. Installed two screws back to air passage tube for lint trap through two holes in top that were removed at beginning of repair. Install lint trap, turn on circuit breaker and verified operation. Put wet clothes in tub, turned machine on, put away two screw drivers and kissed wife apologizing for taking so long to getting around to repairing machine.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Frank from ENDICOTT, NY
Parts Used:
279570
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers
broken door catch
Took 3 screws out used the putty knife to pry the door a part then used the pliers to remove the old door catch and then sapped the new one and put the door back together and I was was done in less than 10 min.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the 1106818610
121 - 135 of 462