1106318731 Kenmore Dryer - Instructions

First diagnose the problem. No air coming out the exhaust or filter, things aren’t drying, you can’t hear the blower running.
Fuses or breakers are verified ok and on.
Turn dryer off. Disconnect exhaust tubing after unscrewing it’s clamp. Drag the dryer away from the wall to get access to the back and unplug the 220 v power cable from its socket. Get behind the dryer to remove its back cover plate by unscrewing its holding screws with screwdriver or small socket wrenches.
Vacuum out the back of the dryer removing the powdery dust around the blower motor and pulley and remove the old belt.
Since there is no adjustment arm, you have to stretch the belt around the rim of the blower pulley with both thumbs pulling upward against the motor pulley below.
After the belt is in place you can pull on it to be sure both pulleys rotate so the blower fan will rotate. Then just put the back plate on the dryer, replug it in, push it back enough to hook up the exhaust pipe and push the dryer back to its home spot.
Turn it on and you’re ready to go. Then order a spare belt for the future in about 5 + years.

Disconnect dryer.
Unscrew the two screws that hold the door actuator assemby.
replace broken spring.
Screw the the two screws back.

This was rather easy to fix. I had never opened the dryer before but had a serviceman come out so I knew that you can pop the top of the dryer off by putting a flat edge screwdriver in between the top and bottom and popping up. You must remove the screws from the lint dryer before so the top comes off. The piece to replace had two screws and that was it. To get a repairmen from Sxxrs where we purchased it 15 years ago they charge a flat fee of $75 just to come out. That does not include the repair just a fee to come and tell you how much more it would cost to fix it. I ordered the part for less than $5 and $12 more for 2-3 day delivery! What a bargin! I was back drying clothes 15 minutes after the part arrived! Very happy that the part is still being made!

Before beginning, unplugged dryer. 1) Used putty knife at each front corner of top to pop lid loose from clips. 2) Removed hex screws at back of control panel to allow lid to tip open. 3) With lid opened, removed hex screw from inside-top of each side to allow front to pull open from side panels and access door switch easily. 4) Removed clip that holds retaining wires from top. 5) Pulled wire from each side of door switch. 6) Removed switch assembly using Phillips screwdriver to remove two screws mounting switch at top of door opening. 7) Removed broken actuator spring and replaced. 8) Reversed process to reassemble.

Two screws holding top, unhook wire conector. remove cabinet,replace switch. Reassemble.

My dryer is 35 years old and thought this was it, but I googled the question and found out it was the door switch. Orderd the part and received it very fast and didn't want to wait for my husband to come home so I went on you tube and found a video how to open dryer and change switch. I did it in about 30 min. and yes it is now perfect again. No problems. I just unscrewed the old switch and put the new one in. Maybe I'll get another 35 years out of this machine. :o) Thanks for making it so easy.

Replaced lid switch, but problem still continued.

I take the screws out of the door, I removed the catch from behind inside the dryer door, I slid the new catch in the door and snapped it in place. After getting a new catch in the door I put the door back together and put the screws in. Easy repair

Watched the videos for the repairs on the site. Took the back of the dryer off after unplugging the appliance. Removed the failed fuse and thermostat and replaced them both per the video steps. It took about 25 minutes for both parts and the dryer now works well.

Just slipped it on, it was very simple. My dry cylces were reduced. Worth the $15 I spent to get the part!!!!

just followed the video directions, worked perfectly thanks

removed screws that held the door face to gain access to catch replaced catch reassembled door tried dryer works great!

Incredibly simple! You just pop the other plastic catch out with a butter knife and pop the other on in. This is the second time I have done this over the last 4 years or so.

I followed your short video and found it very easy to do

Turned off circuit breaker to machine. Removed lint trap to allow removal of two Philips screws from vent passage that hold lid on. Opened door and removed two Philips screws that hold switch to front of machine. Using flat blade #2 screw driver pushed on plastic locking tabs under front of machine top about 2" in from either side to allow top to be lifted up from machine. While holding up at 45 degree angle reached in and grabbed switch to pull it out for easy access. Set top down gently once switch was out. While holding switch removed broken switch actuator and installed new actuator on to switch. Lifted top back to 45 degree angle and with left hand held switch assembly in place and started two screws previously removed back into actuator holes. Tightened screws snugly. Lowered top back into plastic locking tabs and gently pushed down to secure top. Installed two screws back to air passage tube for lint trap through two holes in top that were removed at beginning of repair. Install lint trap, turn on circuit breaker and verified operation. Put wet clothes in tub, turned machine on, put away two screw drivers and kissed wife apologizing for taking so long to getting around to repairing machine.