Models > 11086379310 > Instructions

11086379310 Kenmore Dryer - Instructions

Jump to:

All Instructions for the 11086379310
121 - 135 of 451
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Michael from Goddard, KS
Parts Used:
279570
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
broken door catch
the part fit perfectly, it just snaped right into place.
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Diana from Canfield, OH
Parts Used:
279570
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers, Wrench (Adjustable)
dryer door won't stay shut
I replaced the male end first hoping that a change in the female part would not be needed. Unfortunately no. I used needle nosed pliers to pry the male part out and pushed the new part in. The female part of the door catch was more difficult. I didn't do it in "textbook" form, but got the job done with pliers and a screwdriver. Worth every penny to fix correctly instead of rigging it. Do it!
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Debra from Oakland, NJ
Parts Used:
279570
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers
door latch broke
Pop out the old latch and replaced with a new one
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Frank from Union Beach, NJ
Parts Used:
279570
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
The door whould not close enough for the dryer to work.
Got my parts very quickly.
Popped out the old door latch with a screw driver and pressed in the new one.
Very simple.
Thanks Parts Select.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Melody from TEXARKANA, TX
Parts Used:
279570
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
Dryer door wouldn't catch and stay shut
I take the screws out of the door, I removed the catch from behind inside the dryer door, I slid the new catch in the door and snapped it in place. After getting a new catch in the door I put the door back together and put the screws in. Easy repair
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
william from KILLEEN, TX
Parts Used:
279570
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
door would stay closed
just replaced parys
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Ronald from Tulsa, OK
Parts Used:
279827
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers, Screw drivers
Loud hum but wouldn't work with a load in
Googled the symptoms the cure was replace the motor. There was a video done by parts select that made the process even easier. Had it done in about 25 minutes.
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Mark from TERREBONNE, OR
Parts Used:
WP691581
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Machine would not start and light stayed on with door closed.
Turned off circuit breaker to machine. Removed lint trap to allow removal of two Philips screws from vent passage that hold lid on. Opened door and removed two Philips screws that hold switch to front of machine. Using flat blade #2 screw driver pushed on plastic locking tabs under front of machine top about 2" in from either side to allow top to be lifted up from machine. While holding up at 45 degree angle reached in and grabbed switch to pull it out for easy access. Set top down gently once switch was out. While holding switch removed broken switch actuator and installed new actuator on to switch. Lifted top back to 45 degree angle and with left hand held switch assembly in place and started two screws previously removed back into actuator holes. Tightened screws snugly. Lowered top back into plastic locking tabs and gently pushed down to secure top. Installed two screws back to air passage tube for lint trap through two holes in top that were removed at beginning of repair. Install lint trap, turn on circuit breaker and verified operation. Put wet clothes in tub, turned machine on, put away two screw drivers and kissed wife apologizing for taking so long to getting around to repairing machine.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Tammy from glenford, OH
Parts Used:
279570
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Door catch was cracked
Incredibly simple! You just pop the other plastic catch out with a butter knife and pop the other on in. This is the second time I have done this over the last 4 years or so.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Rick from SAN DIEGO, CA
Parts Used:
279570
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
latch was broke
just followed the video directions, worked perfectly thanks
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
j from TAZEWELL, TN
Parts Used:
279570
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers
dryer would not run because catch did not hold tight enough to press door switch.
removed screws that held the door face to gain access to catch replaced catch reassembled door tried dryer works great!
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Barbara from NORTH EASTON, MA
Parts Used:
279570
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers
Door would not stay closed - so dryer kept shutting off
Followed Youtube video - quick & easy
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Gregg from St. Augustine, FL
Parts Used:
279570
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Dryer door would not stay closed
After removing front door panel (2 screws) I removed the old latch catch and replace with the new part. 4 minutes later, the door was back together, the dryer was running and the door was staying closed.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Mark from BLOOMFIELD, CT
Parts Used:
WP694674
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Socket set
Dryer would not start. After first replacing a spare Dryer Thermal Fuse I had it tripped again due to overheating. I then ordered a replacement Dryer Thermal Fuse as well as a cycling thermostat after determining the thermostat was no longer regulating the dryer's temperature.
Watched the videos for the repairs on the site. Took the back of the dryer off after unplugging the appliance. Removed the failed fuse and thermostat and replaced them both per the video steps. It took about 25 minutes for both parts and the dryer now works well.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Susan from HUDSON, MA
Parts Used:
279570
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers
broken door catch
I followed your short video and found it very easy to do
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the 11086379310
121 - 135 of 451