11076972620 Kenmore Dryer - Instructions

My dryer started squeaking and I thought it was the drum rollers, so I bought a set. When I attempted the repair and got as far as removing the dryer drum and I decided to spin the shaft on the motor and that was where the squealing was coming from. I put the rollers on and reassembled the dryer. One day later the motor seized up. Ordered a new motor and installed it with no problems. The nut on the back of the motor ended up being a 20mm wrench. Motor cost me $105.56 and the maintenance kit (ps37308) (2 rollers,4 clips, button clip, new idler pulley and belt) cost $32.08. It cost a total of $137.64 in repairs with no labor costs and I accomplished it in under an hour. Minor handyman skills needed or find a friend who is handy. My dryer is 14 years old and now is running like new again. I used the 50% rule, if a repair exceeds 50% of the cost of a new machine, replace it, if the repair can be done for less than 50% of the cost of a new on, fix it.

Followed the instructions, removed the back cover, disconnected the top, disconnected the element and removed the element holder, then the element. Reversed procedure to install the new part.

Like others have descibed, place Dryer on back and remove two hex head screws on back two phillips screws under lint cover, front is "clamped" with two plastic clips that I popped with a standard screwdriver. The door has two screws on the door switch, I removed these although I'm not sure I needed to. Lift the front out of the way. Look at the belt before you remove it, the tensioner pully isn't screwed in place and drops once the belt is removed. It isn't hard to figure out how it goes back together, but you might as well save the swearing. Remove the belt and the drum lifts out. Remove the old seal and glue the new one in place. Another repair suggested clothes pins to hold the seal while it dried, but I opted for some spring clamps with a little more grip. While the seal dries vaccuum the inside of the dryer and vent pipe clean everthing up good by the time you're done the glue is dry. Put the drum back in using a putty knife to slip the seal in place. re assemble in reverse order of disassembly. If I were doing this repair again I would have bought the front seal too. It doesn't appear to get as much wear as the back, but while you have it open why not? Repair easier than expected, but took more time with the cleaning and glue dry time.

Take out 2 philips screws in lint trap holder on top. Use flat screwdriver to pry up front left and right of dryer top near outside edges and tilt up out of the way. Remove 2 push-on AC connectors on door switch and remove plastic clip holding wires to dryer's front top metal edge. Remove (2) 5/16" sheet metal screw on inside top left and right edges to free up front panel. Lift front panel about an inch and it'll then pull off. It helps to have a second person to help hold or remove the drum at this point. It took 3 times for me to guess right on the squeak. First time I replaced the belt, second time I replaced these rollers, third and final time I replaced the idler pulley, the shaft of which had worn completely off so clearly i can't figure out how we didn't see (or hear) it the first two times! Dri-Slide lube helped stop the squeaking the first two times, but it always returned until this time, now I have a thoroughly rebuilt dryer for the next generation! (PS vacuum out the bottom of the dryer while it's open to remove both lint and greasy roller shavings - do this FIRST and you'll have cleaner hands & clothes!)

After un-plugging the frig and allowing it to defrost, we emptied the frig and gave it a thorough cleaning inside and outside. I then removed the shelving in the freezer and the face plate at the back of the machine. One of the defrost heater coils had burned out and there was a loss of continuity which was keeping the frig from defrosting properly. The old heater snapped out easily. I went to this website and ordered a new defrost heater assembly which arrived practically overnight. It was identical to the old one and installed as quickly and easily as the original had come out. I put the faceplate back on, put the shelving back in, placed a thermometer inside the fresh food section, plugged it in and waited until I heard ice cubes drop. The fresh food section was holding at 41 degrees F which is optimum. The refrigerator has been working smoothly every since! Easy job!

As the instructions say: first remove the drum. In the case of my dryer the drum is supported by two rollers on the back panel and the opening in the front panel. Remove the front panel and the drum almost falls out.

Replacing the seal was easy . Just tear out the old seal, lightly sand the rear lip, stretch the new seal over it, being sure the stitching is oriented properly, and then squeeze adhesive from the supplied tube between the seal and the drum lip.

In putting the dryer back together I couldn't figure out how to thread the belt. I suggest that people attempting this repair take digital pictures of the inside of the appliance before disassembling it.

A very good experience and I prolonged the life of the dryer a good ten more years.

Just put the knob on where old knob was.

Changed out the lint filter

i took the old knob off, went to partselect and ordered the part really easy as their site helped me find the correct part, and put it on with ease when it came in the mail. It works great and PartsSelect helped me be a hero to my wonderful mom. Thanks.

Removed rear panel, removed 3 screws and old element and installed new element. To install new element I only needed one screw and spliced in the two wires that were provided with the element. This repair was simple and now the dryer works great.

I unplugged the dryer from the electrical outlet, removed the back of the unit and checked the heating element for continuity. There was no reading. I then removed the housing and heating element and visually inspected it. The coiled wire was broken in two places.
I then did a Google search with the model number and found Parts Select. I placed my order Sunday afternoon and the part arrived the following Wednesday. That evening it took about 20 minutes to install the new element,put the back on the dryer and re-attach the exhaust tube.
The old dryer is as good as new again.
TJ in Boise

Ordered the motor with pulley and blower wheel in case the wheel did not come free from the motor.
Took out the lint screen, took off the top and disconnected the wires for the door switch, took off the front.
Remove the idler poi and the belt and then removed the drum.
I read in other repair YouTube videos, the blower wheel sometimes is so seized onto the motor axle that you have to remove the wheel by cutting it off.
Yes, ours seized!
Cut off the motor axle with a hacksaw and then the motor and the wheel were free. This was not an issue since I had purchased both the motor and the wheel which I recommend doing anyway. Our dryer over 25 years old and it does not have many electrical components, which I love. We removed the parts put in the new parts. Follow the wiring diagram to get the new motor hooked up.
Then I replaced the drum support rollers, which were a snap and then we put it all back together.
We added an extra step because we had to takeoff the back of the dryer to gain access to the blower. It turned out to be a good thing since years of lint have been trapped at the bottom of the lint chute.
I cleaned everything, washed everything and put it all back together and it purrs like a kitten.
Took us about 2 1/2 hours total since we are very cautious and slow as we didn’t want to break things.
I am very happy with the end result and hopefully it will last another 25 years!
Parts were spot on and worked perfectly.
Much more economical than buying a new dryer for $750-$1000.

I opted to remove front, top and back panels. This is best done with dryer laying on it's back so drum remains in position. Hold panels and pieces in place with masking tape (2") You should block up the dryer so you don't damage the gas pipe. I opted to total shop vac out the piece and lubricate the rollers and tension pulley. I made more in change than the belt cost!

Overall an easy repair. Belt came with diagram for easy threading the belt.

I followed the instructions on the video and it was simple. The hardest part was vacuuming out 32 years of lint from around the motor and igniter. I was lucky there was never a fire in the dryer.

I followed the video. So easy..