41794072300 Kenmore Dryer - Instructions

Took it apart and installed the parts. Then I threw the dryer in the trash and bought a new one.

I watched the video on the repair and followed it. Super easy. Repair only took 30 mins. Please note there are 2 glides. Make sure to order 2.

Watched the online video that showed how to replace the part. Was very easy to follow, but also I did open the inspection plate on the back to make it easier to put the belt on also to make sure that the spring and everything else look okay. As for the door switch took a photo with my phone of how the wires went on remove the wires, popped the old switch out put the new one in put the wires right back up the same way in my photo works perfectly.

Watched video sent to me after I purchased belt on line. Super helpful!

i read reviews and finally found a person that replace the motor, rear bearing, front top glides, and tension arm/pulley.. i had cleaned the fan motor with a tooth brush best i could the 1 time i had it apart. after the 4th time apart and reading a different review that said replace the fan motor housing/fan. i did and noise gone.

I looked up a YouTube video on my specific model. Found one that said “basic disassembly”. I watched that and had it apart and back together in no time. Very easy to take apart and put new parts back in it. Re-assembled and since the repair no squeaking.

Both my husband and I had watched the videos for the parts we ordered. While we had a small space to work in, the repair on our dryer went fine. We are very happy with the parts we ordered along with the short amount of time it took to arrive. Thank you very much for the videos. Purchasing these parts and having the videos really saved us money compared to having to purchase a new dryer.

I took the dryer apart to vacuum and check because of the screaching noise. Took drum out and found the bearing in pieces and shaft had rubbed against the brace. I thought as old as my dryer was I would never get a piece to fix it. I got online and found PartSelect.com. I found the part but could not tell if all was included. there was a Phone Number so I called it. I was helped instantly. They acted like it was no big deal to have a dryer that old. I got my part within a week and had my dryer back together. It works like new. Thank you

Read your article on possible repairs for different symptoms and after dis assembling and cleaning certain parts took a chance on the flame sensor, which turned out to be the culprit. Your help was a valuable tool in the repair process ! What would be the bee's knee's would be the resistance reading on the sensors that monitor the system for a more accurate diagnostic approach. But none the less you definitely aided in the repair of my propane gas dryer. Thank you very much ! And by the way the 3-4 day wait for the part was well worth the half price I paid versus our small town repair facility, Thanx again

I unplugged the dryer and pryed open the top by inserting a screw driver in the space 1inch from the top on the side. After i opened it and lifed it up, I removed the one screw on both sides found in the inner part towards the front top. I then removed the front panel. The coils are toward the bottom left side. They are held in by a bracket which is held in by 2 screws. I removed the outer screw and loosened the inner screw. ( you can remove both screws but it was not necessary).I then swumg the bracket around and was able to lift out the coils. I removed the connectors and relaced the coils. Once done I re-assembled the dryer. The problem was solved.

Dryer was working, only burner was working occasionally only. So, in result the drying time was very long, and clothes were cold and still not satisfactionally dry; occasionally only it was hot. It became obvious to me that gas burner only occasionally is working. On the Internet I found some instructables, mostly on YouTube, but also on this site (the Burner diagram): thus I have learned that the culprit must be the two tiny ignition coils: they worked only sometimes, so it was only a jeopardy when checking them using a continuation meter (voltmeter with continuation feature). For the access to the burner combo I used a small checking door right below the large door, in front wall of the dryer. There are only two small screws which hold a small piece of metal which cover these tiny coils. However, I had to disconnect the burner from gas pipe to get better access to those screws. (Of course, I also disconnected the dryer from power and I had to disconnect those wire connections on the burner combo to get access to the burner). It works perfectly after this repair.

replaced rear drum bearing kit. Watched video made it real easy. The only problem was getting the belt back on the pulleys.

Remove top cover and front and remove drum and install a new bearing kit and new belt.

Blower wheel came apart from molded-in nut, was loose, was rubbing on housing wall, and was likelynot moving to much air. I read some troubled stories about separating the wheel nut from the motor shaft so bought a new motor and blower housing and install wall pretty easy. There are videos on the teardown process and does that long and not alot of parts to keep track of either. I have already done the felt drum liner and rear drum ball and belt so if it's older than 15 years and your going to take the dryer apart, replace all these parts and you will about have new dryer at half the cost of new.

First I took the drum out of the dryer. This was an easy tear down. I had to remember 2 wires, and a belt assembly ( 2 pullies ). I removed 3 screws inside the drum to release the bearing assembly from the back. Then I went to the dryer chasis and removed the mounting bracket by removing 2 screws. I simply replaced the mounting bracket with the new one. This required having to use a magnet to hold a small ball bearing in place while I worked the rest of the pieces in position.I greased it up and went back to the drum. I replaced the old bearing assembly with the new one. Easy. I took the time to shop-vac the inside of the dryer. There was a lot of loose lint, candy rappers, coins, etc. Finally, I put it back together. Unfortunately, this is the forth (4th) time I've had to do this. It's cheaper than buying a new dryer. Now, I've got to fix the washer.