1106517402 Kenmore Dryer - Instructions

took part top of washer saw switch replaced it not to difficult it is always easier when you have new one to look at

My dryer is probably more than 20 years old. I know, I know, but I decided to fix it anyway. I followed the same steps as the other posters here. However, I almost never fix anything like this and the dryer is in a small space with only a couple of inches of clearance on either side.
The repair took 10 hours off and on over 2 days. You will definitely need another set of hands at various times like when you are unscrewing the fan from the motor shaft and when you are reinstalling the drum and belt.
Getting the motor mount clips off the frame was a huge pain and getting the motor back in place and the clips on correctly was a 3 hour learning experience. Make sure you have all the wires hooked back up BEFORE you hook up the motor mount clips. When you seat the motor on the mounts the wiring hookups need to be almost on the bottom. Check the instructions drawing for placement.
You don’t actually remove the fan cover you just unscrew the mounting screws and push it to the side.
Re-hooking up the belt and belt tightener is not intuitive but you will eventually figure it out. I found some generic dryer belt installation drawings on the Internet that showed me how to do it.
The photocopied instructions that come with the motor are kind of fuzzy after a few generations of photocopying.
In the end, it worked! It is also much quieter now.

Removed and replaced motor. In the process of removing old motor, the blower wheel had to be unscrewed from the rear shaft of the motor, in order to remove the motor. In my case, the blower wheel had seized up on the rear shaft and could not be unscrewed. It had to be cut off and it also had to be replaced. The dryer now works fine. Tip: I watched an internet video (repairclinic.com)about the procedure before I started. Very helpful!

I removed the back before I relized that the motor was under the drum. I removed the front and the drum and accessed the motor. I used a small flat head screw driver to prythe brackets that held th motor in place. I had a bit of a problem removing the motor from the fan. Then I read the web site and figured out that the treading was a LEFT thread. Still had some problems and ended up removing the pully wheel and using a pipe wrench to get the fan off the motor.

I wish I had taken a picture of the pully and belt to see how it went back together, but it went back easy enough.

Very pleased with my effort and guess I saved about $300 bucks on the repair, and the 2 plus weeks to get the guy to my house.

the plastic fan can be tricky to get off,hold the pully side of motor with an adjustable wrench and turn plastic nut on fan clockwise.mine busted and i had to order another fan but they are easy to put on. counter clockwise to put back on.(reverse treads)

It was so easy! I simply fit the gasket into the groove where the old one had been. Didn't even need any tools.

I losened the two screws under the flap covering the filter or lint screen. With the screws removed the entire top of the dryer slides forward and hinges up allowing access to the door switch. The door switch is removed by taking two screws out with access obtained by opening the dryer door. Replacing the bracket/switch was easy and a simple reverse of the disassembly put the dryer back together. I would highly recommend doing this repair yourself.

The Door Swith Acuator Spring was broken. I unplugged the dryer. Removed the two screws on the top control panel. Lifted the top of the dryer and propped it up. Then removed the two wires attached to the door switch (remember to label them with tape-one without and one with tape). Then as suggested by a previous "repairman" loosen the two screws that hold the switch just enough to remove the actuator. You do not have to completely remove the screws. Slip in the new actuator and reverse the process. Voila ... you have a new dryer and a very happy better half. I was given a kitchen pass to play golf and savor some "spirit" water.

Advice: Don't slam the dryer door. The actuator will last longer.

>removed 2 screws connecting the vent filter to the top lid of the unit (just in front of removable filter).
>Losing two screws at the back of the machine, just below control panel to allow free movement of the top lid on its hinges.
>Raise top lid & supported open.
>Now have free access to door switch (inside , front right fastened to front panel)
>removed the old switch
>fasten new switch (required new wire connector which was supplied with package) to existing wiring and replaced.
>Works perfectly!

drilled a 7/16 diameter hole directly in the center of the two mounting holes filed it square big enough so as the spring tip fits thru now the door closes on the spring which actuates the switch looks and works perfect.

Googled dryer won't start! From information on the Parts Select website, I determined it was possibly the dryer door switch. Checked the dryer to confirm status of door switch and found it broken! Ordered part and received it within 2 days (actually ordered on a Sunday and it shipped on Monday with receipt on Wednesday. Unpluged the dryer. Used information from Parts select website to remove two screws from vent filter, used screwdriver to pop the top of dryer at each front corner, removed two long screws from the old switch and replaced the broken actuator on the switch with the new actuator received from Parts Select. Note: It was easier to remove old switch with the wires removed from terminals (just pull off), replacing the wires after securing the switch and actuator back in place. Piece of cake, wife happy, received her king of the roost reward :>)) This is also a good time to clean the lint filter area and the hoses to prevent one of those 16,000 annual dryer fires!!!

This was a classic easy repair and I am sure saved us bundles on a service call.

When I ordered the part, I viewed the installation video. That was a key step for me. It told me how to identify the correct part (there are multiple latch pieces in the repair kit, and one of them matches the type of door for the dryer), and how to disassemble the door to get the part installed. When the part came and I installed it, it turned out that I could snap the part in by hand, with no tools. It took about 5 seconds to try it, and it worked.

The dryer just stopped after a new load of clothes was put in. It appeared to be a power problem as there were not warnings, it just stopped. After checking the power, I suspected it was an electrical interlock problem. After nosing around, I traced the power to the dryer door interlock. Sure enough the switch was fine, but the mechanical lever was worn away. After Googling around for a replacement I found PartSelect.Com. Found the part, ordered it, and I am back in business. My wife is not happy though, as she wanted a new dryer:)

The latch for my Kenmore dryer was only $10 with shipping and just what I
needed. No instructions included, so I googled installation and it was fixed
in less than 3 minutes... YEAH... I am happy!