1106708702 Kenmore Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Sheila from MOUNT VERNON, IL
- Parts Used:
- 339392V
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
filter had holes
pulled old filter out and then slid the new filter in Done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from BLOOMFIELD, CT
- Parts Used:
- WP694674
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Dryer would not start. After first replacing a spare Dryer Thermal Fuse I had it tripped again due to overheating. I then ordered a replacement Dryer Thermal Fuse as well as a cycling thermostat after determining the thermostat was no longer regulating the dryer's temperature.
Watched the videos for the repairs on the site. Took the back of the dryer off after unplugging the appliance. Removed the failed fuse and thermostat and replaced them both per the video steps. It took about 25 minutes for both parts and the dryer now works well.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Newport, VT
- Parts Used:
- WP691366
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Socket set
broken belt
removed two screws from lint screen raised top removed two nut screw from front disconnected lid wire lifted front up and off removed drum cleaned all dust out replaced pulley unit with new one (with a wheel) replaced tub held it up with a bungey cord put on new belt and reassembled unit tested out back in business
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- william from KILLEEN, TX
- Parts Used:
- 279570
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
door would stay closed
just replaced parys
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jon from LaGrange, IL
- Parts Used:
- 279827
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
dryer stopped and smelled of smoke.
I reviewed several videos on parts sites and YouTube. There is more than enough advice online showing step-by-step instructions. The only difficulty came with the rear nut holding the motor shaft to the blower fan. I used a crescent wrench with a long pipe over it for added torque. The two spring clips holding the motor in place can be removed and installed with the help of a nutdriver pushing the clip down, . The dryer was new enough so the motor needed no switch changes. The new motor is running fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from LINCOLN, NE
- Parts Used:
- WP238460
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Stepdaughter had over the years broke the 2 cables that supported the drop down door. So she let it hang by the hinges, which eventually broke them also.
Removed what was left of the old hinges, installed the new ones. Also added a length of jack chain (same size chain that’s on a toilet flapper) to one side to support the door while open. Tried to chain up both sides but it wouldn’t let the door completely close and depress the switch. Cables are no longer supplied by any parts dealers.
Was this instruction helpful to you?
Thank you for voting!
Dryer was making all kinds of noises
After checking out the website and the videos posted to YouTube, I decided that I should take a chance and try and repair the problem myself. I am not in any way mechanical, and for me personally, this was a huge job. The instructions and the video were so clear that it made the job easy. Taking out the dryer drum was a concern, and although not heavy, I used a friend to hold it in place when I was putting it back together. My only small issue was when I was removing the rollers. I had some difficulty taking off the plastic locking washers but other than that, it was a breeze. The videos posted are great and very easy to follow. While doing the above job, I also replaced the dryer belt and heating element, both of which I followed instructions as per video. The dryer is running very smooth, and is the quietest it has been for many years. Very happy with all aspects of service advice and videos.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from New Richmond, WI
- Parts Used:
- WP691581
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Light stayed on, inside dryer. Dryer no workie
I diagnosed the problem, as a broken arm on the actuator for the door shut switch. I jumped the switch, and dryer worked. I went to this site, found the part I needed, ordered it/received it quickly, and proceeded to do the repair. The video that THIS particular part goes for, isn't' like MY dryer. My dryer hinges in the rear. You just remove the 2 screws on either side of the control panel, (right and left), pull forward on the panel, to ease its attachment, let it lie. Then with a small plastic pry tool, pop the 2 attaching points in the front of the dryer. Front end lifts up, like a hood on a car. My roommate held hood up, while I R&R'd the switch actuator. Went back together, in reverse of my taking apart. Worked great. Thanks a bunch.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from St. Louis, MO
- Parts Used:
- WPW10512946
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
My daughter threw a heavy wet comforter into the dryer and the tri-ring sheared off.
I ordered the part(and a backup) and had it in two days. 5 days less than ordering from sears.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ava from BALTIMORE, MD
- Parts Used:
- 349241T
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Dryer making excessive noise; then continued to blow circuit
Attributed excessive noise to age of dryer, upon closer inspection, a dish towel had become caught at rear of drum because the drum support rollers were damaged causing the drum to create a space in the rear of the drum. This was large enough for the dish towel to be caught. Originally I thought that the thermal fuse had blown the circuit-which should occur in an overheating situation-however the loose drum had worn through the electrical wire leading to the door switch because it was not properly seated on the rear drum rollers. the wire was repaired with a wire nut, rear drum rollers were installed and it is working again. thank you for the extremely fast shipping
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Marion, KY
- Parts Used:
- WPW10512946, 349241T
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set, Wrench (Adjustable)
Noise in dryer when dryer was turned on
Removed the drum then removed the old parts and installed the new ones. Dryer now runs very quite and heats good. You have very fast service my mother ordered the parts on the net one day and I received the parts next day and did the repair that night and dried clothes. Thanks,
Your great service is very hard to find.
Your great service is very hard to find.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christian from Sunapee, NH
- Parts Used:
- W11613302
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Seal snapped, which lead to longer dry cycles.
Just slipped it on, it was very simple. My dry cylces were reduced. Worth the $15 I spent to get the part!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Theodore from Tyler, TX
- Parts Used:
- 279570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
dryer door wouldn't catch, catch was broken
took the cstch reciever out, with my fingers, pushed the new one in, snap lock fit.......couldn't be better, like repairing a model T ford.......
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Goddard, KS
- Parts Used:
- 279570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken door catch
the part fit perfectly, it just snaped right into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rick from SAN DIEGO, CA
- Parts Used:
- 279570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
latch was broke
just followed the video directions, worked perfectly thanks
Was this instruction helpful to you?
Thank you for voting!