1106718501 Kenmore Dryer - Instructions

1 Vice grips are required to remove the fan/blower. Clamp on inside of dryer so you can remove the blower/fan assembly

Recommend 10" or larger 14" will definitely do the job

2. Blower/fan is reverse threaded when facing the back of the dryer. That is how I broke mine. Turn clockwise to loosen - feels very unnatural

3. If you have to replace the 5 & 6 electrical connectors, you have to have a barrel crimper for insulated terminals - IWISS SN-02C RATCHET TERMINAL CRIMPING PLIER TOOL, 24-14AWG is a good example

After identfying that the problem was due to a damaged drum support roller, I decided to replace the bad roller instead of replacing the dyer itself.

The first thing was to remove the front cover
and the front panels to expose the drum. (Only a few screws hold them in place.) Next, the drum was removed by first releasing the belt from the motor pulley and tensioner, and then pulling the drum straight out.

At this point the two rollers would be exposed. The triangular plastic retaining locks were removed by slightly prying them off. The old rollers were then removed and replaced.

Before putting everything back, this was a good time to vacuum all the accumulated lint inside, especially the lint that had accumulated around the motor assembly and the fire box.

(A pleasant surprise: I found a lot of coins inside the unit, enough to recoup half of what I spent for the new rollers.)

After checking out the website and the videos posted to YouTube, I decided that I should take a chance and try and repair the problem myself. I am not in any way mechanical, and for me personally, this was a huge job. The instructions and the video were so clear that it made the job easy. Taking out the dryer drum was a concern, and although not heavy, I used a friend to hold it in place when I was putting it back together. My only small issue was when I was removing the rollers. I had some difficulty taking off the plastic locking washers but other than that, it was a breeze. The videos posted are great and very easy to follow. While doing the above job, I also replaced the dryer belt and heating element, both of which I followed instructions as per video. The dryer is running very smooth, and is the quietest it has been for many years. Very happy with all aspects of service advice and videos.

Unfortunately after i replaced the new switch the drier worked well. After it stopped for the 2nd time we wanted to put a load and start the swit lost contact. It was not working.It lost the contact with the circuit. No clicking sound the drier not functional. I guess need a new switch?

Removed 2 screws holding the lint trap on top, popped up the top and lifted back, removed 2 screws on the inside top of front panel, lifted front off and set aside then reached under the drum and pulled tension pully to loosen the belt, and removed the drum. popped the motor clams off and then used 2 adjustable wrenches to grasp the nuts at the front and back to remove blower fan. When you look for the area in back to loosen the blower fan you may notice the nut that you are looking for is actually part of the fan and is plastic looking rather than metal. I did have to take off the back cover to the blower fan to tighten it back up.I had seen instructions that the blower fan would have a 3/8 hole in the back of it to loosen it,but mine did not. I assembled it and it works great with my new motor and rollers. I received my part in 2 days, very happy

The repair was easy, removed back panel from dryer, removed heating element w/ shroud, disassembled old heating element from shroud and replaced with new one. New one was a bit bigger, so tension holds it in place, but no worries, works fine now.

would have been nice to know this supplier had a warehouse in Louisville, then I wouldn't have had to eat the 2nd day air shipping I paid for. Would have been happy to pick it up at their warehouse or pay for regular shipping, would have gotten here faster.

I reviewed several videos on parts sites and YouTube. There is more than enough advice online showing step-by-step instructions. The only difficulty came with the rear nut holding the motor shaft to the blower fan. I used a crescent wrench with a long pipe over it for added torque. The two spring clips holding the motor in place can be removed and installed with the help of a nutdriver pushing the clip down, . The dryer was new enough so the motor needed no switch changes. The new motor is running fine.

Pulled out the old element (by removing the two screws that hold it in place) About a couple of inches and disconnected the two wires. I then inserted the new element and screwed it in place and connected the wires. Just took two of us to fix the problem...one to tilt the dryer forward and the other to put in the element.
I am so happy I didn't have to go out and purchase a new dryer........new ones are way too expensive!

Basically, the stories listed on your website had excellent instructions. The important thing to remember is popping the top to get to the upper housing clip. Otherwise, a person might try to pull the element out from the bottom of the housing, which would be a minor disaster. I'm very happy with PartSelect and the website. I'll be back!

pulled old filter out and then slid the new filter in Done

I took out the 2 screws that are located on the top of dryer under the lint filter door. Popped up the whole top of dryer. Opened the dryer door to unscrew the 2 door switch screws. Took off the old broken door switch through the open dryer top and before replacing the new door switch completely I tested it by turning the dryer on and pressing the new switch against the button activator 2 find out if it works. When it did, I carefully put the door switch back so the dryer door can activate it properly and screwed in the 2 screws. Finally, I put the dryer top back down & fastened the last 2 screws under the lint filter door.

Removed what was left of the old hinges, installed the new ones. Also added a length of jack chain (same size chain that’s on a toilet flapper) to one side to support the door while open. Tried to chain up both sides but it wouldn’t let the door completely close and depress the switch. Cables are no longer supplied by any parts dealers.

One screw held element. Removed back of dryer. Removed screw, pulled out failed element. Slid new element in. Put in and tightened screw. Replaced back. Only two problems: screw head was pointed away; replacing air duct to wall tube (always is a problem for me).

Attributed excessive noise to age of dryer, upon closer inspection, a dish towel had become caught at rear of drum because the drum support rollers were damaged causing the drum to create a space in the rear of the drum. This was large enough for the dish towel to be caught. Originally I thought that the thermal fuse had blown the circuit-which should occur in an overheating situation-however the loose drum had worn through the electrical wire leading to the door switch because it was not properly seated on the rear drum rollers. the wire was repaired with a wire nut, rear drum rollers were installed and it is working again. thank you for the extremely fast shipping

Took of the btm pan and the top to be able to remove the front. Raised the drum enough to replace the right hand wheel. ( the old ones had already been removed) Replace the left hand wheel and bracket. Re assemble the machine. Worst part was trying to do all this with the can of beer in one hand!!