1106818600 Kenmore Dryer - Instructions

Turn off Gas, unplug electric cord, remove rear cover, remove two screws holding the lint trap to the top, raise top flip[ping to the back supporting it not to damage wiring, remove bottom front cover, remove door springs, remove front cover, disengage belt tensioner, remove drum. unclip right side roller and remove, unbolt left wheel mount from the rear and the bracket in the front, remove clips or cut off (new ones come with new clips). clean the wheel shafts, light sanding if needed, apply light coat of lithium grease. replace wheels and reassemble dryer in the reverse order from disassemble. roll drum by hand after front back on to ensure it rolls without catching. Finish and test.

It went well, I followed the instruction video and referred back to it if any questions or difficulty. The instructor on the video was obviously very experienced and duplicating his actions exactly was very helpful, One thing I noticed that wasn't mentioned was that the thread on the wheel / motor is left handed.

I followed the advice that was already published for my Dryer. I removed the cover on the rear of the Dryer, Disconnected the two wires attached to the Heating Element. I positioned the Dryer on its side so that it was easier to remove the one sheet metal screw holding the Heating Element in a metal box. Removed the old Heating element. I found where to coil was open. Installed the new Heating element. Put everything back together. Turned the dryer on and there was heat in the Dryer. Thanks to all who posted for the excellent advice.

Had to replace the rear felt seal and the motor. It was no problem to find videos on how to do both of these repairs. Took apart the appliance. When the parts came first replaced the drum rear felt seal and waited for the motor to be delivered. Then replaced the motor as per online instructions. Also went to Home Depot to buy a new flexible dryer tube since the old one had a few holes. It works perfectly again.

First unplug appliance, Remove dryer top and front. remove drum and belt. Two clamps hold motor in place. remove them and lint chute housing in rear, exposing the fan. Use vice grips to hold motor shaft behind belt pulley flat spot. Remove fan, it's reverse threads. A large adjustable wrench on plastic fan nut and spray lubricant if very tight. Place new motor next to old and switch wires over, crimp on new 1/8'' connectors. Remember the green ground wire may need an allen wrench. Put back drum,belt, lube the rollers and replace back cover, front, top.

After removing the back (five nut screws), lifting the top (two lint filter screws), I diagnosed the problem (timer, fuse and sensors tested OK - heating element broken). I uninstalled the heating element cage sensors (three nut screws) but did not unwire them. Then I removed the heating element cage (one nut screw on top and lift) - the right angle screwdriver was very helpful. I removed the broken element (one nut screw on bottom). Ordered from Parts Select online because they had the element for a better price & quicker expedited shipping than Sears. As soon as the part arrived (two days!), I rewired and installed the element and assembled the dryer in the reverse order of the above process. Total time from package arrival to drying clothes (BIG stack) - 30 minutes!

I watched a U Tube video about banging sound from dryer. Once I recognized the problem, lifted the top, removed 2 screws holding the front, removed the drum, and bingo. Saw the worn out drum roller. Ordered the replacement parts from "PartSelect" on line (Great Company). Was in no hurry, so I chose regular mail delivery. 4 days later, got the correct replacement parts, put the dryer back together, and now, the dryer is quieter then when I bought it new, a thousand years ago. I will never again be afraid to tackle an appliance issue. THANK YOU !!!

I followed the on-line video. I am extremely happy I made the effort and successfully fixed my dryer on my own. It sure beats a new dryer expense or high repair cost.

just like the guy in the video. It was easy to folow his instructions, and the best thing of all i could stop the video if I had a question and then resume!

re-placed screen

Used the dryer illustrated parts list to find the heater. Used a multi-meter to determine that the heater had no resistance, meaning it was open and could not heat. Removed the heating element held to the dryer with one hex screw with a wrench. Purchased a replacement heating element and received it within 2 days. Screwed the new heating element with a hex wrench again. The dryer works like new now.

Dryer was taking long time to dry cloths, electric bill seemed higer than usual, used 1/4" nutdriver, removed rear panel, opened top cover w/screw driver to pry with, marked all wires with blk tape to id them later. Did thorugh inspect/clean of link section to propeller baleds 1 hr, continuity check of heater, switches etc found heater lower than spec, ordered heater, continued to clean all sections & vents, installed new vent hose, pulled about 2lbs of sand, dust, lint from all sections, heater works great now, clothes dry quick. New heater core came in mail and installed it. The newer elecment was 5200 watts, orig was 5400 watts, ohms was same, size etc. The unit works like a charm. Notes:Did not check or lubricat the drum. Drum is very squeaky, belt in good shape. Dryer is 20yrs old. Will replace when I can afford it! for now I can live with some sqeaks, anyway as I am getting older my hearing is going away, Good luck.

Disconnect dryer.
Unscrew the two screws that hold the door actuator assemby.
replace broken spring.
Screw the the two screws back.

This was rather easy to fix. I had never opened the dryer before but had a serviceman come out so I knew that you can pop the top of the dryer off by putting a flat edge screwdriver in between the top and bottom and popping up. You must remove the screws from the lint dryer before so the top comes off. The piece to replace had two screws and that was it. To get a repairmen from Sxxrs where we purchased it 15 years ago they charge a flat fee of $75 just to come out. That does not include the repair just a fee to come and tell you how much more it would cost to fix it. I ordered the part for less than $5 and $12 more for 2-3 day delivery! What a bargin! I was back drying clothes 15 minutes after the part arrived! Very happy that the part is still being made!

1 Vice grips are required to remove the fan/blower. Clamp on inside of dryer so you can remove the blower/fan assembly

Recommend 10" or larger 14" will definitely do the job

2. Blower/fan is reverse threaded when facing the back of the dryer. That is how I broke mine. Turn clockwise to loosen - feels very unnatural

3. If you have to replace the 5 & 6 electrical connectors, you have to have a barrel crimper for insulated terminals - IWISS SN-02C RATCHET TERMINAL CRIMPING PLIER TOOL, 24-14AWG is a good example