1106607931 Kenmore Dryer - Instructions

all that was required was to push the catch into the slot notools needed.

You can buy the switch AND lever/latch, but partselect had lever by itself which is all I needed. Pay attention to orienation of lever around switch when you take old latch off and attach new. Also, be careful to not drop new lever behind/beneath clothes dryer drum. Took my wife and I a while to fish it out. I have replaced heating element, and other parts. At some point it will be time for a new dryer...

I disconnected the dryer from the electric. I removed the lid to the dryer by first removing the lint door screws and prying the lid off properly. Disconnected the wires to the door switch. Removed the screws from inside the door and carefully removed teh actuator. Seperated the actuator from the switch and replaced the broken actuator. Reinstalled the actuator and switch and screwed the assembly back in place. Reconnected the wires, lowered the dryer lid and screwed the lint door screws back in place. It Worked perfectly.

I squeezed the latch catch with a pair of pliers and pushed it in the catch hole. But that was the final repair. There were two "repairs" before that. First, we used two commercial grade rolls of wide plastic tape to tape the dryer door shut each time we used it, for a year, until we ran out of tape. Second, we positioned a chest of drawers in front of the dryer and wedged a 1" x 4" against the door. Very effective. Then I broke down and ordered the $3 catch.

Opened up every panel EXCEPT the front, then discovered how easy that is. Replacement belt was a snap to install. I noticed some plastic collar thing on the driveshaft appeared to have melted. Did not appear to be critical part, so I put it together and tested it out. Seems to work fine. I think the collar is there to prevent the belt from potentially slipping off the driveshaft.

First I was told by the maytag repair man that the motor was shot and it would be 467 dollars to repair. Since I didn't have that kind of money I decided to take it apart to see if I could replace the motor myself. Once I had it apart I saw the part that held the motor in place was broken off and the motor was out of place causing it too shut itself off. Once I figured it all out it took about 2 minutes to replace the less than 6 dollar part! Thanks partSelect!!!

I pried open the top of the dryer, removed the 2 scrws holding the front cover of the dryer, un hooked the dryer drum buide belt, removed the dryer drum - all this just to get to the drum support roller. The bottom roller - the rubber on the wheel had been "chewed of". I can only guess because too much weight was placed in the dryer with wet clothes.
I removed the triangle shaped retaining clip, using the mini flat head screw-driver, slid the damaged roller off, replaced the new roller, and installed the new retaining clip. To install the new clip, I used a 1/2inch nut driver. I did the same to replace the upper drum support roller. The actual repair took less than 5 minutes, However, the prep time in dismanteling the dryer in order to get to the drumm rollers and puting the dryer back to gether consumed the bulk of my time.

Followed the instruction given by previous writers in these post.
Hint The bungee cord hook was used to hold up the lid, worked very well.
If you are by yourself use duct tape to hold the drum in place before removing the front panel. Tape the top rear of the drum to the rear frame. Also do this when reassembling the front panel.
Easy and quick makes the wife happy this time.
PS. Ordered the parts on Sunday and had them on Tuesday.

When i finally got sick and tired of hearing it when she used the dryer. I popped the top flipped it up unscrewed the 2 screws holding the front panel of the body on, picked up on it and pulled it off the drum. I then reached back to the rear right corner and stretched the tentioner and pulled the belt off the motor pulley.Then I picked up the belt and the drum and pulled it out of the dryer body. After seeing the drum support roller that is mounted on the base, and back of the left side I decided to go online and find this sight that had the drum support rollers as a set with the keepers and the push nut for the brace as a set for a really fair price. If your unit has a warranty "do not" take anything apart and do not order any pats until you check with your dealer. You do not want to void your warranty. I then pulled off the push nut and then i took the screw that held on the brace in front of the worn out drum roller, then pryed off the keeper and pull off the drum roller, took off the back keeper;inspect the shaft if it is not damaged ,(this one was not),then you wait until the parts arrive, yes your dryer will set in parts for about a week, but believe me in todays economy its worth "not having to buy a new dryer" at least for this small repair. When the parts arrive everything is pretty much in reverse of how you took it apart dont forget your cell phone is also a camera that can be a "memory enhancer" for when you get this far. Also be nice to your wife your going to need a little help putting it back together. Of course if she wants her dryer back she needs to help anyways. patience is a virtue and if you dont take your time and do this right it will be tested the drum and belt need to be fitted right and held up to get both the belt on the pulley and around the tentioner and get the front panel lined up on the front of the drum good luck and pass your knowledge on its getting to be a lost art.

Followed the video instructions to replace motor, belt, and rollers (belt and rollers looked to be in ok shape, but as long as I had the thing open I figured I might as well). Fairly straightforward procedure. Trickiest parts were getting the rear roller clips in place and re-attaching the rear motor spring clip. Probably could've found a used dryer of comparable quality for less, but this was easier and more satisfying than moving dryers in and out of the basement.

Removed back and then removed lint slide.
Vacuumed all of the cabinet and and washed lint chute.
Blower seal and lint seals were crumbling since dryer is 24
years old. Part Select diagrams and repair videos are extremely helpful in showing the process. Dryer now working like new.

I never received my part checked back after said hearing part had been shipped was told part was no longer available have called twice about my refund and not received that either

Removed top, then remove front panel, then removed the drum, and the idler pulley assembly. Then added new parts, and reversed procedure to assemble back to new.actually runs better, now. Dryer is approximately 30 years old.

re-placed screen

the video was very well done and able to understand. disconnect power ,remove lint trap,remove 2 phillps head screws, push putty knife in front seam line about 1'' in from corners to release top assembly ,lift up and support, disconnect wire connector ,remove 1 screw in each front corner lift front panel off while holding drum, remove broken belt,install new belt with grooves against drum ,feed around tensioner pulley and onto motor shaft pulley ,spin drum by hand to make sure belt tracking etc. reassembly in reverse.