11068062800 Kenmore Dryer - Instructions

Didn't have a putty knife, so used a flathead screwdriver to carefully pop out the top, then bottom of the catch. New one easily popped in. Took less than one minute!

Did not take the door off..applied adhesive and seal fit perfectly..used packaging wide tape to secure for a bit while adhesive dried..waited 24 hrs..holding well..dryer is back to working order..thank you..I received the seal in 2 days after ordering!!

Looked up on the internet, saw a video, ordered the part using model of dryer, got the part in 7 days, took out old part and snapped in the new door latch. Now it works good as new

Took a screwdriver and bent wings out a little and then was able to get hold of it with a pair of pliers. Then just put the new unit in the opening and tapped it in. If I had a good pair of needle pliers, it would not have been necessary for the screwdriver.

I looked up the problem on Utube and saw a demo on what three items to check with a volt meter for continuity or resistence on either the start button, the door switch, or the thermal fuse. The first two checked out OK but the fuse was dead, no resistance or ohmns on the voltmeter. I had trouble locating it on my dryer as the Utube site said to pull the rear cabinet off when actually it was under the front panel below the dryer door sitting in an awkward position right on top of the dryer motor. I used 2 flat head screwdrivers to pry open the latches over the panel door that are located about 4 inches in from either end and then used a small right angle screwdriver with a flash light propped against the heating elements (after I removed the cover plate) to see with and to give me more room to loosen just two tiny screws that attached the fuse to the motor. Voila! It works better than before.

Unplugged dryer, removed bottom front panel, removed fan cover. I used a 1/4 ratchet to remove 2 screws and the old fuse. Installed new fuse, fan cover, and front panel. Dryer works great!

I saw a couple of videos to replace this but found a simpler way to replace the heating element on my dryer. DISCONNECT the POWER.
I removed the lower panel (6 screws). Dis-connected two wires; one going to the heat sensor in the back and the other to the switch at the front. Removed the two screws to the metal plate in front of the heating element. Slid the whole heating assembly out. Removed the screws holding the heating element in the housing. Removed the failed (open) heating element and installed the new one. Reversed the process for re-assembly.

Shut off the hot water supply (pretty sharp eh?). Disconnected the hose from the hw supply and the at the connection to the washing machine. These had not been touched in at least 15 years and were somewhat tough to loosen but finally came ..... accessibility was a problem for the connection to the water supply as it was in a recessed wall box. Fortunately, we had some washers for the hose connections so the install was a snap. Hardest part of the whole job was moving the washing machine out from between the drier and the wash tub .... tight fit. Thanks for the quick service and to FED EX for their delivery. The delivery fellow was a real gentleman.

Easy manually

Just insert filter.

Use the adjustable wrench to remove the water line. Remove the dryer vent line. Take off the screws on the main back panel, the screws connecting the top. Place both off the side. Unscrew and remove the parts connecting to the heat line located on the left side. Remove the front unit screw attaching the heat line to the bottom of the dryer. Remove the four screws connecting the top and bottom of the heat line together. The two on the left side is a huge pain, make sure you have small hands to be able to reach on the side of the line. Pull the bottom of the heat line loose. The heating element is inside the line. Replace element and put everything back in the order it was removed.

This was so easy to take apart and put back together following the repair video. I figure my family saved $200.00 by doing it myself.

Exchanged old for new.

had no room to work in the back of the dryer

i removed the old lens,then removed the bulb,after ordering and receiving your replacement lense,it went back on just like the old one.the repair was very easy. thank you. D.S P.S1 IAM A REPIARMAN NOW!!! WITH YOUR VIRTUAL REPAIRMAN APP,VERY VERY SMART ILL SPREAD THE WORD.