11086742702 Kenmore Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Mike from New Windsor, MD
- Parts Used:
- WP3392519
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
Dryer did not start.
Removed Back and found schematic. Found fuses on schamatic and parts inside dryer. Checked fuses and thermal fuses with an ohm meter and found one that was open. Went to Parts select and ordered part. Relpaced the part and dryer works like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- WILFRED from NORTH HIGHLANDS, CA
- Parts Used:
- 279570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
I recieved the kit the next day after ordering. It took about two seconds to do the repair
all that was required was to push the catch into the slot notools needed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Doug from Toledo, OR
- Parts Used:
- WP3392519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Dryer would not start, light worked door swicth worked
First I removed the top back plate and found the electrical schematic, found the fuse and themostat. Went to Whilpool web site found exploded parts list to identify part (fuse)
removed fuse and tested with MM for an open. It was. Shorted the leads to verify that the Dryer operated. Found your site and was easily able to identify the part from the excellent description and pictures. Ordered it, installed it work great thanks
removed fuse and tested with MM for an open. It was. Shorted the leads to verify that the Dryer operated. Found your site and was easily able to identify the part from the excellent description and pictures. Ordered it, installed it work great thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from WARREN, NJ
- Parts Used:
- 279570
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dryer door latch broke and door wouldn’t stay shut.
Jimmied out the latch using two screw drivers to get under the edges. Pushed the new piece in. Voila! Took 2 minutes for what my repair man told me would cost about $200 to fix. Unbelievable!!( I first watched some YouTube videos to get the idea )
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Clark from Clarksville, VA
- Parts Used:
- WP3392519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Dryer wouldn't run
tested continuity, determined thermal fuse was open. PartSelect sent a new fuse very quickly, and it was just a matter of reconnecting the wires and putting the back cover on the dryer. Started right up.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JoAnn from ANTHONY, FL
- Parts Used:
- WP3392519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Had heat, but clothes did not dry.
Unplugged dryer, unscrewed back, and replaced fuse. Easy as 123. Video showed what to do step by step! I am not a handy man, just a woman trying to be money5 smart. Anyone could do this and save on home repairs.
Was this instruction helpful to you?
Thank you for voting!
Part broken in half
Remove screws, dryer sensor on screen. Put sensor back in place. Secure with screws. The way you take it off go in reverse.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Burlington, CT
- Parts Used:
- WP3392519
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
The dryer would not start and the timer would not advance
I checked the Thermal Fuse and it was okay. Then I tested the timer and it was not working. Then I ordered the timer from this site and installed it in about 30 min. The dryer is now working.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Allen from KENNETT, MO
- Parts Used:
- WP8577274
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Shutting off and had to wait before could turn back on
Followed online video very easy and dryer works like new one....
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from Kennewick, WA
- Parts Used:
- WP3392519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Dryer wouldn't start. Timer ran but that was it.
Went on line and determined the problem was the thermal fuse. Removed the rear panel of the dryer, removed the leads from the thermal fuse, hooked them together and started the dryer. That confirmed the problemwas the existing fuse.Ordered the new thermal fuse, installed the fuse, hooked up the wires and it works finel Very simple fix. About a 10 year old dryer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from COWARD, SC
- Parts Used:
- WP8544771
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers, Socket set
Heater element had burnt open and would not heat.
I found a simple video on YouTube. I removed the front panel and door. I removed drum and belt drive. Heater element was then easily accessible. I removed all wires after taking pictures of wiring. Element was secured by one screw and one clip and was easily removed. Removed element from element cover. Checked thermostat and thermal overload. Put new element inside of element cover. Then replaced everything in reverse order. Removing lint from inside of dryer was probably the most difficult part of repair. Had to have assistance from my son to put drum belt back on but rest of replacement was simple.
Was this instruction helpful to you?
Thank you for voting!
Dryer wouldn't Heat up. Otherwise all else worked
Thought I could do it myself. Bought most parts recommended by this site
Took backoff thinking I could get to heating element. Noticed I would have to take out drum. Being in my 90's, decided to call repairman. He came and replaced the heating element I had purchased. He didn't have to come back
after he had purchased parts. That saved about half my bill. Worked Great!
Took backoff thinking I could get to heating element. Noticed I would have to take out drum. Being in my 90's, decided to call repairman. He came and replaced the heating element I had purchased. He didn't have to come back
after he had purchased parts. That saved about half my bill. Worked Great!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carl from MARION, KY
- Parts Used:
- WPW10359272
- Difficulty Level:
- Really Easy
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Socket set
Rollers making a noise.
Removed the top, removed lower front cover, removed the front, removed the belt, removed the drum and the back. Removed and replaced roller support shaft and drum roller’s. Completed all Front and rear support for drum. Replaced drum , replaced drum roller belt and replaced back, completed replacement of the top, front.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from WELLS, MN
- Parts Used:
- WP8544771
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Socket set
Electric Heating Element went out.
I checked continuity of all electrical points. I took the top off, then the back, and front of the dryer off so it was easy to inspect the whole dryer. I was also able to clean unwanted dust, and lent with a shop vacuum by doing this.
Keep track of different screws, and mark each screw location with a permanent magic marker. Taking pictures with camera phone is very helpful. Pay attention to electrical connections as well, some of those will need to be dismantled.
Try not to take apart anything more than needed. Watching some online video's can be very helpful as well.
If uncomfortable doing this, call a service repair technician.
I'm a farm boy, and repairs usually come easy to me, but not always.
Keep track of different screws, and mark each screw location with a permanent magic marker. Taking pictures with camera phone is very helpful. Pay attention to electrical connections as well, some of those will need to be dismantled.
Try not to take apart anything more than needed. Watching some online video's can be very helpful as well.
If uncomfortable doing this, call a service repair technician.
I'm a farm boy, and repairs usually come easy to me, but not always.
Was this instruction helpful to you?
Thank you for voting!
Idler Pulley squealing - Worn out
Before anything unplug the dryer
1) Remove the back panel to include electric cable. 2) Remove the lower front panel. 3) Remove top panel. 4) Remove control panel 5) remove door assembly to include metal frame and front panel of the blower housing. (much easier than trying to do this separately. 6) Remove drum belt by pulling back on the idler pulley (spring). 7) Remove drum. 8) Remove idler pulley retaining ring and pulley. 9) remove old seal on blower housing. 10) I added high temp grease to the pulley shaft and installed new pulley. 11) Install new blower seal. 12) Install drum and new belt. 13) Re-install all the panels.
1) Remove the back panel to include electric cable. 2) Remove the lower front panel. 3) Remove top panel. 4) Remove control panel 5) remove door assembly to include metal frame and front panel of the blower housing. (much easier than trying to do this separately. 6) Remove drum belt by pulling back on the idler pulley (spring). 7) Remove drum. 8) Remove idler pulley retaining ring and pulley. 9) remove old seal on blower housing. 10) I added high temp grease to the pulley shaft and installed new pulley. 11) Install new blower seal. 12) Install drum and new belt. 13) Re-install all the panels.
Was this instruction helpful to you?
Thank you for voting!