11097086601 Kenmore Dryer - Instructions

remove top, front, drum, fan fan housing, replace motor

My gas dryer would run with heat for 5 minutes in all settings, but kick off and not heat again. Timer would not advance in autodry. Thought it was the cycling thermostat, so replaced that, but did not solve the issue. Ordered the coils, and cleaned out heavily clogged lint from bottom of lint trap, especially right above the fan motor at the bottom of the trap. Received the coils, opened the top and front, took out drum, and replaced the coils. The replacement took less than 2 minutes. Be careful putting the drum back on to make sure the felt is not caught inside the drum. You can give it a spin to make sure. Wear gloves, as I cut myself up pretty good on the edges of the dryer body. The inside of my dryer looks like a crime scene! Anyway, I put it back together, and it runs great. Solved the timer advance issue in autodry, and the heat kicks on and off when it is supposed to. Good luck! Thanks Part Select!

Followed standard instructions regarding removal of top first & then the front panels. Realized after following this process that I did not have to remove top, but only one of front panels to obtain access to moisture sensor. If I have to do this again, the replacement of sensor will be much easier.

Watched youtube video to problem shoot. Cause determined to be coils bad. Searched web found Parts Select to be easiest site to deal with and had coils for best price. Followed instructions supplied with parts. Dryer works like new.

Removed the screws replaced the belt and lubricated the wheels and that fixed my Knocking and it runs like when I first got it

took 2 screws out and replace new coils

Removed the front panel, removed the tub and removed the old seal. Tub seal area was scraped, sanded and wiped with acetone to ensure a clean. Bonding surface. Applied adhesive with and acid brush to get a consistent adhesive layer without getting too much in any one place. Seal was a bit smaller than the tub circumference so it had to be stretch to fit. While the adhesive was curing , I took the time to clean the contact surfaces and vacuum the lint from inside the cabinet. Reinstalled the tub, drive belt and front panel.

Took the top off and then front off and drum out . Replaced Drum roller and shaft support bolts.

Removed the dryer door, unscrewed lint vent.

Checked fuse with Volmeter, had continuity (acted as a short) not the problem. Disconnected Hot Surface Igniter 2 Position connector to check resistance for a range of 50-300 Ohms of resistance with Voltohm Meter. Meter read open (High Resistance). Removed Igniter by unscrewing 5/16" hex nut on igniter plate assembly and noticed silicon carbide element was cracked in the middle. Ordered a new igniter and noticed assembly was required. Be careful here as igniter element is fragile, also do not touch it with your bare hands. You have to lay down on floor to reinstall igniter assembly and you might want to practice anchoring the defective igniter to gain confidence. Finally with slow movements anchored new igniter assembly and turned on dryer. Watched igniter glow heating gas valve and heating gas flame returned. Dryer fixed for a few hours of study online and cost only $24, plus learned how the gas dryer works.

I ordered the top 5 items that may cause this problem based on the troubleshooting guide presented by the technicians I found in youtube. I replaced the coils and that fixed the problem. The coils are the first to go out according to techs, but I have the other parts just in case I may need them later on. My Maytag dryer which is over 19 years old is alive and working again. The coils are accessible from the bottom access panel secured by 2 nut screws, unplug the dryer first, then the coils are secured by a bracket with 2 small philips head screw, I used a stubby philips screw driver to remove the bracket, undo the 2 electrical connectors on the coils one with 2 prongs and the other with 3 prongs. Put the new coils attached the electrical connectors and secured them with the bracket. Checked for any loose wiring ensuring connectors are secured in place, then test run the dryer with the panel off so you can see the if the flame stays on, if you run the dryer without wet clothes the flame may stop after 15 or so minutes. It is better to test run the dryer with wet clothes just like when your drying fresh washed and wringed clothes. It was really easy, good luck!

Took the old parts out and installed the new parts in , everything that you sent fit perfect!!!!!

remove 3 screws vent comes out put new part in works grate just like new a gain

YOU NEVER SENT ME THE PARTS!!!
I had to drive to a parts store to find them. On January 17, 2024, I tried to call you when the parts did not arrive and your recording said there were no reps available and you hung up. WE CANNOT GET HELP TO CANCEL THIS ORDER. We have been going in circles with PartSelect and shipping. SO, how do I get my refund of the $107.26 for the parts that I never received!!

How to repair E1 error/fault on Whirlpool Duet dryer model GEW9200LW0 please watch that video very helpful.