11084182401 Kenmore Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Ramon from Los Angeles, CA
- Parts Used:
- 349241T
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers
Dryer was making a lot of noise while running.
After identfying that the problem was due to a damaged drum support roller, I decided to replace the bad roller instead of replacing the dyer itself.
The first thing was to remove the front cover
and the front panels to expose the drum. (Only a few screws hold them in place.) Next, the drum was removed by first releasing the belt from the motor pulley and tensioner, and then pulling the drum straight out.
At this point the two rollers would be exposed. The triangular plastic retaining locks were removed by slightly prying them off. The old rollers were then removed and replaced.
Before putting everything back, this was a good time to vacuum all the accumulated lint inside, especially the lint that had accumulated around the motor assembly and the fire box.
(A pleasant surprise: I found a lot of coins inside the unit, enough to recoup half of what I spent for the new rollers.)
The first thing was to remove the front cover
and the front panels to expose the drum. (Only a few screws hold them in place.) Next, the drum was removed by first releasing the belt from the motor pulley and tensioner, and then pulling the drum straight out.
At this point the two rollers would be exposed. The triangular plastic retaining locks were removed by slightly prying them off. The old rollers were then removed and replaced.
Before putting everything back, this was a good time to vacuum all the accumulated lint inside, especially the lint that had accumulated around the motor assembly and the fire box.
(A pleasant surprise: I found a lot of coins inside the unit, enough to recoup half of what I spent for the new rollers.)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from ENDICOTT, NY
- Parts Used:
- 279570
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
broken door catch
Took 3 screws out used the putty knife to pry the door a part then used the pliers to remove the old door catch and then sapped the new one and put the door back together and I was was done in less than 10 min.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tammy from glenford, OH
- Parts Used:
- 279570
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Door catch was cracked
Incredibly simple! You just pop the other plastic catch out with a butter knife and pop the other on in. This is the second time I have done this over the last 4 years or so.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Theresa from STOCKTON, CA
- Parts Used:
- WP3406105
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dryer wouldn’t stop spinning/2weeks later didn’t turn on at all
Lift up top portion of dryer inside the front wall is the electrical part which attaches to the door switch
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from UPPR MARLBORO, MD
- Parts Used:
- 279570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Broken dryer door catch
Followed the video instructions which were comprehensive, easily understood, and prefaced with a listing of necessary tools. Completely satisfied with parts and supplementary information.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from NORTH EASTON, MA
- Parts Used:
- 279570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Door would not stay closed - so dryer kept shutting off
Followed Youtube video - quick & easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christian from Sunapee, NH
- Parts Used:
- W11613302
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Seal snapped, which lead to longer dry cycles.
Just slipped it on, it was very simple. My dry cylces were reduced. Worth the $15 I spent to get the part!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Theodore from Tyler, TX
- Parts Used:
- 279570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
dryer door wouldn't catch, catch was broken
took the cstch reciever out, with my fingers, pushed the new one in, snap lock fit.......couldn't be better, like repairing a model T ford.......
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Goddard, KS
- Parts Used:
- 279570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken door catch
the part fit perfectly, it just snaped right into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rick from SAN DIEGO, CA
- Parts Used:
- 279570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
latch was broke
just followed the video directions, worked perfectly thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- j from TAZEWELL, TN
- Parts Used:
- 279570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
dryer would not run because catch did not hold tight enough to press door switch.
removed screws that held the door face to gain access to catch replaced catch reassembled door tried dryer works great!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carrie from PLAINFIELD, IL
- Parts Used:
- WP691366
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Dryer drum wasn't turning
Found the belt was broken and the pulley wheel had melted, replaced the belt and the pulley, could not have been simpler. Watched the video on how to repair and in less than 15 mins was fixed. Saved a lot of money by doing it myself.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from HUDSON, MA
- Parts Used:
- 279570
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
broken door catch
I followed your short video and found it very easy to do
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Melody from TEXARKANA, TX
- Parts Used:
- 279570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Dryer door wouldn't catch and stay shut
I take the screws out of the door, I removed the catch from behind inside the dryer door, I slid the new catch in the door and snapped it in place. After getting a new catch in the door I put the door back together and put the screws in. Easy repair
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from NORTH READING, MA
- Parts Used:
- WP3406105
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Kept running with door open.
Replaced switch very easy to do.
Was this instruction helpful to you?
Thank you for voting!