11087701701 Kenmore Dryer - Instructions

I saw a couple of videos to replace this but found a simpler way to replace the heating element on my dryer. DISCONNECT the POWER.
I removed the lower panel (6 screws). Dis-connected two wires; one going to the heat sensor in the back and the other to the switch at the front. Removed the two screws to the metal plate in front of the heating element. Slid the whole heating assembly out. Removed the screws holding the heating element in the housing. Removed the failed (open) heating element and installed the new one. Reversed the process for re-assembly.

I googled the problem and determined that the thermistor was faulty. I found your web site from which I ordered the replacement part. The part arrived within a week. The replacement was not particularly difficult, but the space was very tight (without removing more panels and covers). I just kept at it and got it installed and the dryer works fine now. There are several pertinent videos on you tube, none of which were my particular model, but the combination of them led me to a successful installation.

Determined via multimeter that either the thermostat or thermal fuse were not working, so ordered the kit (best value, contains both parts).Easiest access is from the rear, so removed rear panel and top of dryer (required) and also the vent tube since it was in the way. Unhooked wires from both parts, used socket to remove nuts holding each one on, put new ones in place, re-attached wires. Replaced vent tube, vacuumed entire inside of dryer (good idea). Put back/top back on and the dryer worked/heated perfectly immediately.

Seemed daunting but pull the front off and the drum is basically just perched inside on some rollers. You have to pull it out to really reach in and wrap the 96”+ band around it and to motor and don’t forget to tension it with tension pulley if you don’t see that if your belt broke!
Another bonus is after 10 years I got to remove the softball size fur ball rolling in the squirrel cage fan , big help on air flow!!!

I ordered the part(and a backup) and had it in two days. 5 days less than ordering from sears.

Started by using the parts select troubleshooting guide. Didn't think that the drive belt could possibly be broken as the dryer wouldn't start. The non turning drum caused the "thermistor" to blow.

This repair looks intimidating but really is very easy.

Thanks Part Select!

first of all there is no video for this model dryer (cabrio accu-dry) the main difference is that the console is removed by removing 3 screws across the back top of console then using putty knife release spring fastener on each side ,slide forward and lift. remove one screw at top of control board and remove from plastic mount,and unplug connecting wires.remove top of cabinet lifting up and forward. The rest of install is typical to other models. The back panel doesn't come off this model. You have to access everything from the front.

Disassemble top and front of dryer removed drum. R2 pulley and belt. Cleaned and reassemble front door ops checked working order of machine . Replaced top. I thank you wife is happy.

I removed the top first followed along with removing the side bracket that holds the circuit board. I then proceeded with removing the bottom cover and front panel. I disconnected the front panel from the control board and was able to slide the front panel upward. The door and blower housing was a bit tricky to pull out without thinking I was damaging something. I then replaced all the seals and cleaned the dryer after removing the drum and belt. I also replaced the drum support rollers. Afterwards I put everything back together and had an "E1" error and I pulled the thermostat out and wiped it down from all the lint and dryer worked perfect after that. Dryer takes the right amount of time to day clothes and no more rumbling noise. The instructions videos were VERY helpful.

Had to call service company to come and do the repair and they had the correct parts. PARTSELECT is a very terrible company to do business with. They sent incorrect parts and will not answer the phone or respond to emails after two weeks. will report to BBB.

You tube

Pretty easy repair and I am not very handy. I believe they engineer these machines so you hire someone to do the job. They could place that part in an area where it is easier to get to, like a door on the side or something

Took back panel off, and it was really easy putting the new idler pulley in.

Message indicated something amiss in the motor circuit. Followed Instructions in the on-board manual. Turned out to be the internal-bias thermostat, and the exhaust air thermistor both. Changed faulty parts, cleaned lint from the system and we are off and running again.
Thank You.
DW Pranger

It was a lot easier then I thought. Just watch the tutorial of how to fix it on this website and you wont have a problem.